fusion/lsi/mpi_log_sas.h

0001 /* SPDX-License-Identifier: GPL-2.0 */
0002 /***************************************************************************
0003  *                                                                         *
0004  *  Copyright (c) 2000-2008 LSI Corporation.  All rights reserved.         *
0005  *                                                                         *
0006  * Description                                                             *
0007  * ------------                                                            *
0008  * This include file contains SAS firmware interface IOC Log Info codes    *
0009  *                                                                         *
0010  *-------------------------------------------------------------------------*
0011  */
0012
0013 #ifndef IOPI_IOCLOGINFO_H_INCLUDED
0014 #define IOPI_IOCLOGINFO_H_INCLUDED
0015
0016 #define SAS_LOGINFO_NEXUS_LOSS      0x31170000
0017 #define SAS_LOGINFO_MASK        0xFFFF0000
0018
0019 /****************************************************************************/
0020 /*  IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF                            */
0021 /*  Format:                                                                 */
0022 /*      Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3)                             */
0023 /*      Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR               */
0024 /*      Bits 23-16: LOGINFO_CODE                                            */
0025 /*      Bits 15-0:  LOGINFO_CODE Specific                                   */
0026 /****************************************************************************/
0027
0028 /****************************************************************************/
0029 /* IOC_LOGINFO_ORIGINATOR defines                                           */
0030 /****************************************************************************/
0031 #define IOC_LOGINFO_ORIGINATOR_IOP                      (0x00000000)
0032 #define IOC_LOGINFO_ORIGINATOR_PL                       (0x01000000)
0033 #define IOC_LOGINFO_ORIGINATOR_IR                       (0x02000000)
0034
0035 #define IOC_LOGINFO_ORIGINATOR_MASK                     (0x0F000000)
0036
0037 /****************************************************************************/
0038 /* LOGINFO_CODE defines                                                     */
0039 /****************************************************************************/
0040 #define IOC_LOGINFO_CODE_MASK                           (0x00FF0000)
0041 #define IOC_LOGINFO_CODE_SHIFT                          (16)
0042
0043 /****************************************************************************/
0044 /* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP          */
0045 /****************************************************************************/
0046 #define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS                 (0x00010000)
0047 #define IOP_LOGINFO_CODE_UNUSED2                             (0x00020000)
0048 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE                 (0x00030000)
0049 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT              (0x00030100) /* Route Table Entry not found */
0050 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN              (0x00030200) /* Invalid Page Number */
0051 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM            (0x00030300) /* Invalid FORM */
0052 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT              (0x00030400) /* Invalid Page Type */
0053 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM             (0x00030500) /* Device Not Mapped */
0054 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST         (0x00030600) /* Persistent Page not found */
0055 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT         (0x00030700) /* Default Page not found */
0056
0057 #define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE         (0x0003E000) /* Tried to upload from flash, but there is none */
0058 #define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE         (0x0003E001) /* ImageType field contents were invalid */
0059 #define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE           (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */
0060 #define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occurred while attempting to upload the entire flash */
0061 #define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED       (0x0003E004) /* Error occurred while attempting to upload single flash region */
0062 #define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE                (0x0003E005) /* Problem occurred while DMAing FW to host memory */
0063
0064 #define IOP_LOGINFO_CODE_DIAG_MSG_ERROR                      (0x00040000) /* Error handling diag msg - or'd with diag status */
0065
0066 #define IOP_LOGINFO_CODE_TASK_TERMINATED                     (0x00050000)
0067
0068 #define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R         (0x00060001) /* Read Action not supported for SEP msg */
0069 #define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R      (0x00060002) /* Invalid Bus/ID in SEP msg */
0070
0071 #define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED            (0x00070001)
0072 #define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED       (0x00070002)
0073 #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO            (0x00070003)
0074 #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO          (0x00070004)
0075 #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ      (0x00070005)
0076
0077 #define IOP_LOGINFO_CODE_LOG_TIMESTAMP_EVENT                 (0x00080000)
0078
0079 /****************************************************************************/
0080 /* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL            */
0081 /****************************************************************************/
0082 #define PL_LOGINFO_CODE_OPEN_FAILURE                         (0x00010000) /* see SUB_CODE_OPEN_FAIL_ below */
0083
0084 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_NO_DEST_TIME_OUT       (0x00000001)
0085 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATHWAY_BLOCKED        (0x00000002)
0086 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE0          (0x00000003)
0087 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE1          (0x00000004)
0088 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE0        (0x00000005)
0089 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE1        (0x00000006)
0090 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP0              (0x00000007)
0091 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP1              (0x00000008)
0092 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RETRY                  (0x00000009)
0093 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BREAK                  (0x0000000A)
0094 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0B              (0x0000000B)
0095 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP       (0x0000000C)
0096 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D              (0x0000000D)
0097 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL      (0x0000000E)
0098 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BAD_DEST               (0x00000011)
0099 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP          (0x00000012)
0100 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP          (0x00000013)
0101 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0      (0x00000014)
0102 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON1      (0x00000015)
0103 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON2      (0x00000016)
0104 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON3      (0x00000017)
0105 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_STP_RESOURCES_BSY      (0x00000018)
0106 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_WRONG_DESTINATION      (0x00000019)
0107
0108 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATH_BLOCKED           (0x0000001B) /* Retry Timeout */
0109 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_AWT_MAXED              (0x0000001C) /* Retry Timeout */
0110
0111
0112
0113 #define PL_LOGINFO_CODE_INVALID_SGL                          (0x00020000)
0114 #define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH        (0x00030000)
0115 #define PL_LOGINFO_CODE_FRAME_XFER_ERROR                     (0x00040000)
0116 #define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW                  (0x00050000)
0117 #define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET          (0x00060000)
0118 #define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR       (0x00070000)
0119 #define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR      (0x00080000)
0120 #define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS      (0x00090000)
0121 #define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE                (0x000A0000)
0122 #define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR           (0x000B0000)
0123 #define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR            (0x000C0000)
0124 #define PL_LOGINFO_CODE_SATA_LINK_DOWN                       (0x000D0000)
0125 #define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS            (0x000E0000)
0126 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE                  (0x000F0000)
0127 #define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED            (0x000F0001) /* PL not yet initialized, can't do config page req. */
0128 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT               (0x000F0100) /* Invalid Page Type */
0129 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS         (0x000F0200) /* Invalid Number of Phys */
0130 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP          (0x000F0300) /* Case Not Handled */
0131 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV           (0x000F0400) /* No Device Found */
0132 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM             (0x000F0500) /* Invalid FORM */
0133 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY              (0x000F0600) /* Invalid Phy */
0134 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER         (0x000F0700) /* No Owner Found */
0135 #define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT             (0x00100000)
0136 #define PL_LOGINFO_CODE_RESET                                (0x00110000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE) */
0137 #define PL_LOGINFO_CODE_ABORT                                (0x00120000) /* See Sub-Codes below  (PL_LOGINFO_SUB_CODE)*/
0138 #define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED                  (0x00130000)
0139 #define PL_LOGINFO_CODE_IO_EXECUTED                          (0x00140000)
0140 #define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER        (0x00150000)
0141 #define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT                     (0x00160000)
0142 #define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY        (0x00170000)
0143 #define PL_LOGINFO_CODE_IO_CANCELLED_DUE_TO_R_ERR            (0x00180000)
0144 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE                     (0x00000100)
0145 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT     (0x00000101)
0146 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_SATA_NEG_RATE_2HI   (0x00000102)
0147 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_RATE_NOT_SUPPORTED  (0x00000103)
0148 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_BREAK               (0x00000104)
0149 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ZONE_VIOLATION      (0x00000114)
0150 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON0            (0x00000114) /* Open Reject (Zone Violation) - available on SAS-2 devices */
0151 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON1            (0x00000115)
0152 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON2            (0x00000116)
0153 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON3            (0x00000117)
0154 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT         (0x0000011A) /* Open Reject (Retry) Timeout */
0155 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATH_BLOCKED        (0x0000011B)
0156 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED           (0x0000011C) /* Arbitration Wait Timer Maxed */
0157
0158 #define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET                 (0x00000120)
0159 #define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER                  (0x00000130)  /* Leave lower nibble (1-f) reserved. */
0160 #define PL_LOGINFO_SUB_CODE_PORT_LAYER                       (0x00000140)  /* Leave lower nibble (1-f) reserved. */
0161
0162
0163 #define PL_LOGINFO_SUB_CODE_INVALID_SGL                      (0x00000200)
0164 #define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH    (0x00000300)
0165 #define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR                 (0x00000400)
0166 /* Bits 0-3 encode Transport Status Register (offset 0x08) */
0167 /* Bit 0 is Status Bit 0: FrameXferErr */
0168 /* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */
0169 /* Bit 3 is Status Bit 18 WriteDataLenghtGTDataLengthErr */
0170
0171 #define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW              (0x00000500)
0172 #define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET      (0x00000600)
0173 #define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR   (0x00000700)
0174 #define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR  (0x00000800)
0175 #define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS  (0x00000900)
0176 #define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE            (0x00000A00)
0177 #define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR       (0x00000B00)
0178 #define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR        (0x00000C00)
0179 #define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN                   (0x00000D00)
0180 #define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS        (0x00000E00)
0181 #define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET       (0x00000E01)
0182 #define PL_LOGINFO_SUB_CODE_SECOND_OPEN                      (0x00000F00)
0183 #define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT         (0x00001000)
0184 #define PL_LOGINFO_SUB_CODE_BREAK_ON_SATA_CONNECTION         (0x00002000)
0185 /* not currently used in mainline */
0186 #define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK              (0x00003000)
0187 #define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK_AIP          (0x00004000)
0188 #define PL_LOGINFO_SUB_CODE_BREAK_ON_INCOMPLETE_BREAK_RCVD   (0x00005000)
0189
0190 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE          (0x00200000) /* Can't get SMP Frame */
0191 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR             (0x00200010) /* Error occurred on SMP Read */
0192 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR            (0x00200020) /* Error occurred on SMP Write */
0193 #define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL      (0x00200040) /* Encl Mgmt services not available for this WWID */
0194 #define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED    (0x00200050) /* Address Mode not suppored */
0195 #define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM               (0x00200060) /* Invalid Slot Number in SEP Msg */
0196 #define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT          (0x00200070) /* SGPIO not present/enabled */
0197 #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED        (0x00200080) /* GPIO not configured */
0198 #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR           (0x00200090) /* GPIO can't allocate a frame */
0199 #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR     (0x002000A0) /* GPIO failed config page request */
0200 #define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR      (0x002000B0) /* Can't get frame for SES command */
0201 #define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR               (0x002000C0) /* I/O execution error */
0202 #define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED      (0x002000D0) /* SEP I/O retries exhausted */
0203 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR      (0x002000E0) /* Can't get frame for SMP command */
0204
0205 #define PL_LOGINFO_DA_SEP_NOT_PRESENT                        (0x00200100) /* SEP not present when msg received */
0206 #define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR                (0x00200101) /* Can only accept 1 msg at a time */
0207 #define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE           (0x00200102) /* ISTWI interrupt recvd. while IDLE */
0208 #define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE           (0x00200103) /* SEP NACK'd, it is busy */
0209 #define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK                (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */
0210 #define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM              (0x00200105) /* SEP stopped or sent bad chksum in Hdr */
0211 #define PL_LOGINFO_DA_SEP_STOP_ON_DATA                       (0x00200106) /* SEP stopped while transferring data */
0212 #define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA                 (0x00200107) /* SEP stopped while transferring sense data */
0213 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1          (0x00200108) /* SEP returned unknown scsi status */
0214 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2          (0x00200109) /* SEP returned unknown scsi status */
0215 #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP            (0x0020010A) /* SEP returned bad chksum after STOP */
0216 #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA    (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/
0217 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND                (0x0020010C) /* SEP doesn't support CDB opcode f/w location 1 */
0218 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_2              (0x0020010D) /* SEP doesn't support CDB opcode f/w location 2 */
0219 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_3              (0x0020010E) /* SEP doesn't support CDB opcode f/w location 3 */
0220
0221
0222 /****************************************************************************/
0223 /* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR            */
0224 /****************************************************************************/
0225 #define IR_LOGINFO_RAID_ACTION_ERROR                           (0x00010000)
0226 #define IR_LOGINFO_CODE_UNUSED2                                (0x00020000)
0227
0228 /* Amount of information passed down for Create Volume is too large */
0229 #define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH                (0x00010001)
0230 /* Creation of duplicate volume attempted (Bus/Target ID checked) */
0231 #define IR_LOGINFO_VOLUME_CREATE_DUPLICATE                     (0x00010002)
0232 /* Creation failed due to maximum number of supported volumes exceeded */
0233 #define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS                      (0x00010003)
0234 /* Creation failed due to DMA error in trying to read from host */
0235 #define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR                     (0x00010004)
0236 /* Creation failed due to invalid volume type passed down */
0237 #define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE           (0x00010005)
0238 /* Creation failed due to error reading MFG Page 4 */
0239 #define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR                      (0x00010006)
0240 /* Creation failed when trying to create internal structures */
0241 #define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR      (0x00010007)
0242
0243 /* Activation failed due to trying to activate an already active volume */
0244 #define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME          (0x00010010)
0245 /* Activation failed due to trying to active unsupported volume type  */
0246 #define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE       (0x00010011)
0247 /* Activation failed due to trying to active too many volumes  */
0248 #define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES          (0x00010012)
0249 /* Activation failed due to Volume ID in use already */
0250 #define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE          (0x00010013)
0251 /* Activation failed call to activateVolume returned failure */
0252 #define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED               (0x00010014)
0253 /* Activation failed trying to import the volume */
0254 #define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED      (0x00010015)
0255 /* Activation failed trying to import the volume */
0256 #define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_PHYS_DISKS       (0x00010016)
0257
0258 /* Phys Disk failed, too many phys disks */
0259 #define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS              (0x00010020)
0260 /* Amount of information passed down for Create Pnysdisk is too large */
0261 #define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH              (0x00010021)
0262 /* Creation failed due to DMA error in trying to read from host */
0263 #define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR                   (0x00010022)
0264 /* Creation failed due to invalid Bus TargetID passed down */
0265 #define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID             (0x00010023)
0266 /* Creation failed due to error in creating RAID Phys Disk Config Page */
0267 #define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR           (0x00010024)
0268
0269
0270 /* Compatibility Error : IR Disabled */
0271 #define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED                  (0x00010030)
0272 /* Compatibility Error : Inquiry Command failed */
0273 #define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED                 (0x00010031)
0274 /* Compatibility Error : Device not direct access device */
0275 #define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS              (0x00010032)
0276 /* Compatibility Error : Removable device found */
0277 #define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND                (0x00010033)
0278 /* Compatibility Error : Device SCSI Version not 2 or higher */
0279 #define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER          (0x00010034)
0280 /* Compatibility Error : SATA device, 48 BIT LBA not supported */
0281 #define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED   (0x00010035)
0282 /* Compatibility Error : Device does not have 512 byte block sizes */
0283 #define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK      (0x00010036)
0284 /* Compatibility Error : Volume Type check failed */
0285 #define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED       (0x00010037)
0286 /* Compatibility Error : Volume Type is unsupported by FW */
0287 #define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE        (0x00010038)
0288 /* Compatibility Error : Disk drive too small for use in volume */
0289 #define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL                 (0x00010039)
0290 /* Compatibility Error : Phys disk for Create Volume not found */
0291 #define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND            (0x0001003A)
0292 /* Compatibility Error : membership count error, too many or too few disks for volume type */
0293 #define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT               (0x0001003B)
0294 /* Compatibility Error : Disk stripe sizes must be 64KB */
0295 #define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE            (0x0001003C)
0296 /* Compatibility Error : IME size limited to < 2TB */
0297 #define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D)
0298
0299 /* Device Firmware Update: DFU can only be started once */
0300 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_DFU_IN_PROGRESS            (0x00010050)
0301 /* Device Firmware Update: Volume must be Optimal/Active/non-Quiesced */
0302 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_DEVICE_IN_INVALID_STATE    (0x00010051)
0303 /* Device Firmware Update: DFU Timeout cannot be zero */
0304 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_INVALID_TIMEOUT            (0x00010052)
0305 /* Device Firmware Update: CREATE TIMER FAILED */
0306 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_NO_TIMERS                  (0x00010053)
0307 /* Device Firmware Update: Failed to read SAS_IO_UNIT_PG_1 */
0308 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_READING_CFG_PAGE           (0x00010054)
0309 /* Device Firmware Update: Invalid SAS_IO_UNIT_PG_1 value(s) */
0310 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_PORT_IO_TIMEOUTS_REQUIRED  (0x00010055)
0311 /* Device Firmware Update: Unable to allocate memory for page */
0312 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_ALLOC_CFG_PAGE             (0x00010056)
0313
0314
0315 /****************************************************************************/
0316 /* Defines for convenience                                                  */
0317 /****************************************************************************/
0318 #define IOC_LOGINFO_PREFIX_IOP                          ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP)
0319 #define IOC_LOGINFO_PREFIX_PL                           ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL)
0320 #define IOC_LOGINFO_PREFIX_IR                           ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR)
0321
0322 #endif /* end of file */
0323