Back to home page

OSCL-LXR
 
 

     

0001 // SPDX-License-Identifier: GPL-2.0-or-later
0002 /*
0003 
0004     bttv-cards.c
0005 
0006     this file has configuration information - card-specific stuff
0007     like the big tvcards array for the most part
0008 
0009     Copyright (C) 1996,97,98 Ralph  Metzler (rjkm@thp.uni-koeln.de)
0010                & Marcus Metzler (mocm@thp.uni-koeln.de)
0011     (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de>
0012 
0013 
0014 */
0015 
0016 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
0017 
0018 #include <linux/delay.h>
0019 #include <linux/module.h>
0020 #include <linux/kmod.h>
0021 #include <linux/init.h>
0022 #include <linux/pci.h>
0023 #include <linux/vmalloc.h>
0024 #include <linux/firmware.h>
0025 #include <net/checksum.h>
0026 
0027 #include <asm/unaligned.h>
0028 #include <asm/io.h>
0029 
0030 #include "bttvp.h"
0031 #include <media/v4l2-common.h>
0032 #include <media/i2c/tvaudio.h>
0033 #include "bttv-audio-hook.h"
0034 
0035 /* fwd decl */
0036 static void boot_msp34xx(struct bttv *btv, int pin);
0037 static void hauppauge_eeprom(struct bttv *btv);
0038 static void avermedia_eeprom(struct bttv *btv);
0039 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]);
0040 static void modtec_eeprom(struct bttv *btv);
0041 static void init_PXC200(struct bttv *btv);
0042 static void init_RTV24(struct bttv *btv);
0043 static void init_PCI8604PW(struct bttv *btv);
0044 
0045 static void rv605_muxsel(struct bttv *btv, unsigned int input);
0046 static void eagle_muxsel(struct bttv *btv, unsigned int input);
0047 static void xguard_muxsel(struct bttv *btv, unsigned int input);
0048 static void ivc120_muxsel(struct bttv *btv, unsigned int input);
0049 static void gvc1100_muxsel(struct bttv *btv, unsigned int input);
0050 
0051 static void PXC200_muxsel(struct bttv *btv, unsigned int input);
0052 
0053 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input);
0054 static void picolo_tetra_init(struct bttv *btv);
0055 
0056 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input);
0057 static void tibetCS16_init(struct bttv *btv);
0058 
0059 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input);
0060 static void kodicom4400r_init(struct bttv *btv);
0061 
0062 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input);
0063 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input);
0064 
0065 static void geovision_muxsel(struct bttv *btv, unsigned int input);
0066 
0067 static void phytec_muxsel(struct bttv *btv, unsigned int input);
0068 
0069 static void gv800s_muxsel(struct bttv *btv, unsigned int input);
0070 static void gv800s_init(struct bttv *btv);
0071 
0072 static void td3116_muxsel(struct bttv *btv, unsigned int input);
0073 
0074 static int terratec_active_radio_upgrade(struct bttv *btv);
0075 static int tea575x_init(struct bttv *btv);
0076 static void identify_by_eeprom(struct bttv *btv,
0077                    unsigned char eeprom_data[256]);
0078 static int pvr_boot(struct bttv *btv);
0079 
0080 /* config variables */
0081 static unsigned int triton1;
0082 static unsigned int vsfx;
0083 static unsigned int latency = UNSET;
0084 int no_overlay=-1;
0085 
0086 static unsigned int card[BTTV_MAX]   = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
0087 static unsigned int pll[BTTV_MAX]    = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
0088 static unsigned int tuner[BTTV_MAX]  = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
0089 static unsigned int svhs[BTTV_MAX]   = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
0090 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
0091 static unsigned int audiodev[BTTV_MAX];
0092 static unsigned int saa6588[BTTV_MAX];
0093 static struct bttv  *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL };
0094 static unsigned int autoload = UNSET;
0095 static unsigned int gpiomask = UNSET;
0096 static unsigned int audioall = UNSET;
0097 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET };
0098 
0099 /* insmod options */
0100 module_param(triton1,    int, 0444);
0101 module_param(vsfx,       int, 0444);
0102 module_param(no_overlay, int, 0444);
0103 module_param(latency,    int, 0444);
0104 module_param(gpiomask,   int, 0444);
0105 module_param(audioall,   int, 0444);
0106 module_param(autoload,   int, 0444);
0107 
0108 module_param_array(card,     int, NULL, 0444);
0109 module_param_array(pll,      int, NULL, 0444);
0110 module_param_array(tuner,    int, NULL, 0444);
0111 module_param_array(svhs,     int, NULL, 0444);
0112 module_param_array(remote,   int, NULL, 0444);
0113 module_param_array(audiodev, int, NULL, 0444);
0114 module_param_array(audiomux, int, NULL, 0444);
0115 
0116 MODULE_PARM_DESC(triton1, "set ETBF pci config bit [enable bug compatibility for triton1 + others]");
0117 MODULE_PARM_DESC(vsfx, "set VSFX pci config bit [yet another chipset flaw workaround]");
0118 MODULE_PARM_DESC(latency,"pci latency timer");
0119 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list");
0120 MODULE_PARM_DESC(pll, "specify installed crystal (0=none, 28=28 MHz, 35=35 MHz, 14=14 MHz)");
0121 MODULE_PARM_DESC(tuner,"specify installed tuner type");
0122 MODULE_PARM_DESC(autoload, "obsolete option, please do not use anymore");
0123 MODULE_PARM_DESC(audiodev, "specify audio device:\n"
0124         "\t\t-1 = no audio\n"
0125         "\t\t 0 = autodetect (default)\n"
0126         "\t\t 1 = msp3400\n"
0127         "\t\t 2 = tda7432\n"
0128         "\t\t 3 = tvaudio");
0129 MODULE_PARM_DESC(saa6588, "if 1, then load the saa6588 RDS module, default (0) is to use the card definition.");
0130 MODULE_PARM_DESC(no_overlay, "allow override overlay default (0 disables, 1 enables) [some VIA/SIS chipsets are known to have problem with overlay]");
0131 
0132 
0133 /* I2C addresses list */
0134 #define I2C_ADDR_TDA7432    0x8a
0135 #define I2C_ADDR_MSP3400    0x80
0136 #define I2C_ADDR_MSP3400_ALT    0x88
0137 
0138 
0139 /* ----------------------------------------------------------------------- */
0140 /* list of card IDs for bt878+ cards                                       */
0141 
0142 static struct CARD {
0143     unsigned id;
0144     int cardnr;
0145     char *name;
0146 } cards[] = {
0147     { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878,  "Hauppauge WinTV" },
0148     { 0x39000070, BTTV_BOARD_HAUPPAUGE878,  "Hauppauge WinTV-D" },
0149     { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR,  "Hauppauge WinTV/PVR" },
0150     { 0xff000070, BTTV_BOARD_OSPREY1x0,     "Osprey-100" },
0151     { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" },
0152     { 0xff020070, BTTV_BOARD_OSPREY500,     "Osprey-500" },
0153     { 0xff030070, BTTV_BOARD_OSPREY2000,    "Osprey-2000" },
0154     { 0xff040070, BTTV_BOARD_OSPREY540,     "Osprey-540" },
0155     { 0xff070070, BTTV_BOARD_OSPREY440,     "Osprey-440" },
0156 
0157     { 0x00011002, BTTV_BOARD_ATI_TVWONDER,  "ATI TV Wonder" },
0158     { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" },
0159 
0160     { 0x6606107d, BTTV_BOARD_WINFAST2000,   "Leadtek WinFast TV 2000" },
0161     { 0x6607107d, BTTV_BOARD_WINFASTVC100,  "Leadtek WinFast VC 100" },
0162     { 0x6609107d, BTTV_BOARD_WINFAST2000,   "Leadtek TV 2000 XP" },
0163     { 0x263610b4, BTTV_BOARD_STB2,          "STB TV PCI FM, Gateway P/N 6000704" },
0164     { 0x264510b4, BTTV_BOARD_STB2,          "STB TV PCI FM, Gateway P/N 6000704" },
0165     { 0x402010fc, BTTV_BOARD_GVBCTV3PCI,    "I-O Data Co. GV-BCTV3/PCI" },
0166     { 0x405010fc, BTTV_BOARD_GVBCTV4PCI,    "I-O Data Co. GV-BCTV4/PCI" },
0167     { 0x407010fc, BTTV_BOARD_GVBCTV5PCI,    "I-O Data Co. GV-BCTV5/PCI" },
0168     { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI,    "I-O Data Co. GV-BCTV5/PCI" },
0169 
0170     { 0x001211bd, BTTV_BOARD_PINNACLE,      "Pinnacle PCTV" },
0171     /* some cards ship with byteswapped IDs ... */
0172     { 0x1200bd11, BTTV_BOARD_PINNACLE,      "Pinnacle PCTV [bswap]" },
0173     { 0xff00bd11, BTTV_BOARD_PINNACLE,      "Pinnacle PCTV [bswap]" },
0174     /* this seems to happen as well ... */
0175     { 0xff1211bd, BTTV_BOARD_PINNACLE,      "Pinnacle PCTV" },
0176 
0177     { 0x3000121a, BTTV_BOARD_VOODOOTV_200,  "3Dfx VoodooTV 200" },
0178     { 0x263710b4, BTTV_BOARD_VOODOOTV_FM,   "3Dfx VoodooTV FM" },
0179     { 0x3060121a, BTTV_BOARD_STB2,    "3Dfx VoodooTV 100/ STB OEM" },
0180 
0181     { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" },
0182     { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" },
0183     { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" },
0184     { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" },
0185     { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" },
0186     { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" },
0187     { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS,  "Phoebe TV Master (CPH060)" },
0188 
0189     { 0x00011461, BTTV_BOARD_AVPHONE98,     "AVerMedia TVPhone98" },
0190     { 0x00021461, BTTV_BOARD_AVERMEDIA98,   "AVermedia TVCapture 98" },
0191     { 0x00031461, BTTV_BOARD_AVPHONE98,     "AVerMedia TVPhone98" },
0192     { 0x00041461, BTTV_BOARD_AVERMEDIA98,   "AVerMedia TVCapture 98" },
0193     { 0x03001461, BTTV_BOARD_AVERMEDIA98,   "VDOMATE TV TUNER CARD" },
0194 
0195     { 0x1117153b, BTTV_BOARD_TERRATVALUE,   "Terratec TValue (Philips PAL B/G)" },
0196     { 0x1118153b, BTTV_BOARD_TERRATVALUE,   "Terratec TValue (Temic PAL B/G)" },
0197     { 0x1119153b, BTTV_BOARD_TERRATVALUE,   "Terratec TValue (Philips PAL I)" },
0198     { 0x111a153b, BTTV_BOARD_TERRATVALUE,   "Terratec TValue (Temic PAL I)" },
0199 
0200     { 0x1123153b, BTTV_BOARD_TERRATVRADIO,  "Terratec TV Radio+" },
0201     { 0x1127153b, BTTV_BOARD_TERRATV,       "Terratec TV+ (V1.05)"    },
0202     /* clashes with FlyVideo
0203      *{ 0x18521852, BTTV_BOARD_TERRATV,     "Terratec TV+ (V1.10)"    }, */
0204     { 0x1134153b, BTTV_BOARD_TERRATVALUE,   "Terratec TValue (LR102)" },
0205     { 0x1135153b, BTTV_BOARD_TERRATVALUER,  "Terratec TValue Radio" }, /* LR102 */
0206     { 0x5018153b, BTTV_BOARD_TERRATVALUE,   "Terratec TValue" },       /* ?? */
0207     { 0xff3b153b, BTTV_BOARD_TERRATVALUER,  "Terratec TValue Radio" }, /* ?? */
0208 
0209     { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
0210     { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
0211     { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
0212     { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
0213     { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
0214 
0215     { 0x1430aa00, BTTV_BOARD_PV143,         "Provideo PV143A" },
0216     { 0x1431aa00, BTTV_BOARD_PV143,         "Provideo PV143B" },
0217     { 0x1432aa00, BTTV_BOARD_PV143,         "Provideo PV143C" },
0218     { 0x1433aa00, BTTV_BOARD_PV143,         "Provideo PV143D" },
0219     { 0x1433aa03, BTTV_BOARD_PV143,         "Security Eyes" },
0220 
0221     { 0x1460aa00, BTTV_BOARD_PV150,         "Provideo PV150A-1" },
0222     { 0x1461aa01, BTTV_BOARD_PV150,         "Provideo PV150A-2" },
0223     { 0x1462aa02, BTTV_BOARD_PV150,         "Provideo PV150A-3" },
0224     { 0x1463aa03, BTTV_BOARD_PV150,         "Provideo PV150A-4" },
0225 
0226     { 0x1464aa04, BTTV_BOARD_PV150,         "Provideo PV150B-1" },
0227     { 0x1465aa05, BTTV_BOARD_PV150,         "Provideo PV150B-2" },
0228     { 0x1466aa06, BTTV_BOARD_PV150,         "Provideo PV150B-3" },
0229     { 0x1467aa07, BTTV_BOARD_PV150,         "Provideo PV150B-4" },
0230 
0231     { 0xa132ff00, BTTV_BOARD_IVC100,        "IVC-100"  },
0232     { 0xa1550000, BTTV_BOARD_IVC200,        "IVC-200"  },
0233     { 0xa1550001, BTTV_BOARD_IVC200,        "IVC-200"  },
0234     { 0xa1550002, BTTV_BOARD_IVC200,        "IVC-200"  },
0235     { 0xa1550003, BTTV_BOARD_IVC200,        "IVC-200"  },
0236     { 0xa1550100, BTTV_BOARD_IVC200,        "IVC-200G" },
0237     { 0xa1550101, BTTV_BOARD_IVC200,        "IVC-200G" },
0238     { 0xa1550102, BTTV_BOARD_IVC200,        "IVC-200G" },
0239     { 0xa1550103, BTTV_BOARD_IVC200,        "IVC-200G" },
0240     { 0xa1550800, BTTV_BOARD_IVC200,        "IVC-200"  },
0241     { 0xa1550801, BTTV_BOARD_IVC200,        "IVC-200"  },
0242     { 0xa1550802, BTTV_BOARD_IVC200,        "IVC-200"  },
0243     { 0xa1550803, BTTV_BOARD_IVC200,        "IVC-200"  },
0244     { 0xa182ff00, BTTV_BOARD_IVC120,        "IVC-120G" },
0245     { 0xa182ff01, BTTV_BOARD_IVC120,        "IVC-120G" },
0246     { 0xa182ff02, BTTV_BOARD_IVC120,        "IVC-120G" },
0247     { 0xa182ff03, BTTV_BOARD_IVC120,        "IVC-120G" },
0248     { 0xa182ff04, BTTV_BOARD_IVC120,        "IVC-120G" },
0249     { 0xa182ff05, BTTV_BOARD_IVC120,        "IVC-120G" },
0250     { 0xa182ff06, BTTV_BOARD_IVC120,        "IVC-120G" },
0251     { 0xa182ff07, BTTV_BOARD_IVC120,        "IVC-120G" },
0252     { 0xa182ff08, BTTV_BOARD_IVC120,        "IVC-120G" },
0253     { 0xa182ff09, BTTV_BOARD_IVC120,        "IVC-120G" },
0254     { 0xa182ff0a, BTTV_BOARD_IVC120,        "IVC-120G" },
0255     { 0xa182ff0b, BTTV_BOARD_IVC120,        "IVC-120G" },
0256     { 0xa182ff0c, BTTV_BOARD_IVC120,        "IVC-120G" },
0257     { 0xa182ff0d, BTTV_BOARD_IVC120,        "IVC-120G" },
0258     { 0xa182ff0e, BTTV_BOARD_IVC120,        "IVC-120G" },
0259     { 0xa182ff0f, BTTV_BOARD_IVC120,        "IVC-120G" },
0260     { 0xf0500000, BTTV_BOARD_IVCE8784,      "IVCE-8784" },
0261     { 0xf0500001, BTTV_BOARD_IVCE8784,      "IVCE-8784" },
0262     { 0xf0500002, BTTV_BOARD_IVCE8784,      "IVCE-8784" },
0263     { 0xf0500003, BTTV_BOARD_IVCE8784,      "IVCE-8784" },
0264 
0265     { 0x41424344, BTTV_BOARD_GRANDTEC,      "GrandTec Multi Capture" },
0266     { 0x01020304, BTTV_BOARD_XGUARD,        "Grandtec Grand X-Guard" },
0267 
0268     { 0x18501851, BTTV_BOARD_CHRONOS_VS2,   "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
0269     { 0xa0501851, BTTV_BOARD_CHRONOS_VS2,   "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
0270     { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ,  "FlyVideo 98EZ (LR51)/ CyberMail AV" },
0271     { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" },
0272     { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" },
0273     { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98,   "Lifeview Flyvideo 98" },
0274 
0275     { 0x010115cb, BTTV_BOARD_GMV1,          "AG GMV1" },
0276     { 0x010114c7, BTTV_BOARD_MODTEC_205,    "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" },
0277 
0278     { 0x10b42636, BTTV_BOARD_HAUPPAUGE878,  "STB ???" },
0279     { 0x217d6606, BTTV_BOARD_WINFAST2000,   "Leadtek WinFast TV 2000" },
0280     { 0xfff6f6ff, BTTV_BOARD_WINFAST2000,   "Leadtek WinFast TV 2000" },
0281     { 0x03116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 311" },
0282     { 0x06116000, BTTV_BOARD_SENSORAY311_611, "Sensoray 611" },
0283     { 0x00790e11, BTTV_BOARD_WINDVR,        "Canopus WinDVR PCI" },
0284     { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX,       "Face to Face Tvmax" },
0285     { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" },
0286     { 0x146caa0c, BTTV_BOARD_PV951,         "ituner spectra8" },
0287     { 0x200a1295, BTTV_BOARD_PXC200,        "ImageNation PXC200A" },
0288 
0289     { 0x40111554, BTTV_BOARD_PV_BT878P_9B,  "Prolink Pixelview PV-BT" },
0290     { 0x17de0a01, BTTV_BOARD_KWORLD,        "Mecer TV/FM/Video Tuner" },
0291 
0292     { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" },
0293     { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" },
0294     { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" },
0295     { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" },
0296 
0297     { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" },
0298 
0299     { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" },
0300     { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" },
0301 
0302     /* likely broken, vendor id doesn't match the other magic views ...
0303      * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */
0304 
0305     /* Duplicate PCI ID, reconfigure for this board during the eeprom read.
0306     * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB,  "Hauppauge ImpactVCB" }, */
0307 
0308     { 0x109e036e, BTTV_BOARD_CONCEPTRONIC_CTVFMI2,  "Conceptronic CTVFMi v2"},
0309 
0310     /* DVB cards (using pci function .1 for mpeg data xfer) */
0311     { 0x001c11bd, BTTV_BOARD_PINNACLESAT,   "Pinnacle PCTV Sat" },
0312     { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" },
0313     { 0x20007063, BTTV_BOARD_PC_HDTV,       "pcHDTV HD-2000 TV"},
0314     { 0x002611bd, BTTV_BOARD_TWINHAN_DST,   "Pinnacle PCTV SAT CI" },
0315     { 0x00011822, BTTV_BOARD_TWINHAN_DST,   "Twinhan VisionPlus DVB" },
0316     { 0xfc00270f, BTTV_BOARD_TWINHAN_DST,   "ChainTech digitop DST-1000 DVB-S" },
0317     { 0x07711461, BTTV_BOARD_AVDVBT_771,    "AVermedia AverTV DVB-T 771" },
0318     { 0x07611461, BTTV_BOARD_AVDVBT_761,    "AverMedia AverTV DVB-T 761" },
0319     { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE,    "DViCO FusionHDTV DVB-T Lite" },
0320     { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE,    "Ultraview DVB-T Lite" },
0321     { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE,    "DViCO FusionHDTV 5 Lite" },
0322     { 0x00261822, BTTV_BOARD_TWINHAN_DST,   "DNTV Live! Mini "},
0323     { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2,    "DViCO FusionHDTV 2" },
0324     { 0x763c008a, BTTV_BOARD_GEOVISION_GV600,   "GeoVision GV-600" },
0325     { 0x18011000, BTTV_BOARD_ENLTV_FM_2,    "Encore ENL TV-FM-2" },
0326     { 0x763d800a, BTTV_BOARD_GEOVISION_GV800S, "GeoVision GV-800(S) (master)" },
0327     { 0x763d800b, BTTV_BOARD_GEOVISION_GV800S_SL,   "GeoVision GV-800(S) (slave)" },
0328     { 0x763d800c, BTTV_BOARD_GEOVISION_GV800S_SL,   "GeoVision GV-800(S) (slave)" },
0329     { 0x763d800d, BTTV_BOARD_GEOVISION_GV800S_SL,   "GeoVision GV-800(S) (slave)" },
0330 
0331     { 0x15401830, BTTV_BOARD_PV183,         "Provideo PV183-1" },
0332     { 0x15401831, BTTV_BOARD_PV183,         "Provideo PV183-2" },
0333     { 0x15401832, BTTV_BOARD_PV183,         "Provideo PV183-3" },
0334     { 0x15401833, BTTV_BOARD_PV183,         "Provideo PV183-4" },
0335     { 0x15401834, BTTV_BOARD_PV183,         "Provideo PV183-5" },
0336     { 0x15401835, BTTV_BOARD_PV183,         "Provideo PV183-6" },
0337     { 0x15401836, BTTV_BOARD_PV183,         "Provideo PV183-7" },
0338     { 0x15401837, BTTV_BOARD_PV183,         "Provideo PV183-8" },
0339     { 0x3116f200, BTTV_BOARD_TVT_TD3116,    "Tongwei Video Technology TD-3116" },
0340     { 0x02280279, BTTV_BOARD_APOSONIC_WDVR, "Aposonic W-DVR" },
0341     { 0, -1, NULL }
0342 };
0343 
0344 /* ----------------------------------------------------------------------- */
0345 /* array with description for bt848 / bt878 tv/grabber cards               */
0346 
0347 struct tvcard bttv_tvcards[] = {
0348     /* ---- card 0x00 ---------------------------------- */
0349     [BTTV_BOARD_UNKNOWN] = {
0350         .name       = " *** UNKNOWN/GENERIC *** ",
0351         .video_inputs   = 4,
0352         .svhs       = 2,
0353         .muxsel     = MUXSEL(2, 3, 1, 0),
0354         .tuner_type = UNSET,
0355         .tuner_addr = ADDR_UNSET,
0356     },
0357     [BTTV_BOARD_MIRO] = {
0358         .name       = "MIRO PCTV",
0359         .video_inputs   = 4,
0360         /* .audio_inputs= 1, */
0361         .svhs       = 2,
0362         .gpiomask   = 15,
0363         .muxsel     = MUXSEL(2, 3, 1, 1),
0364         .gpiomux    = { 2, 0, 0, 0 },
0365         .gpiomute   = 10,
0366         .tuner_type = UNSET,
0367         .tuner_addr = ADDR_UNSET,
0368     },
0369     [BTTV_BOARD_HAUPPAUGE] = {
0370         .name       = "Hauppauge (bt848)",
0371         .video_inputs   = 4,
0372         /* .audio_inputs= 1, */
0373         .svhs       = 2,
0374         .gpiomask   = 7,
0375         .muxsel     = MUXSEL(2, 3, 1, 1),
0376         .gpiomux    = { 0, 1, 2, 3 },
0377         .gpiomute   = 4,
0378         .tuner_type = UNSET,
0379         .tuner_addr = ADDR_UNSET,
0380     },
0381     [BTTV_BOARD_STB] = {
0382         .name       = "STB, Gateway P/N 6000699 (bt848)",
0383         .video_inputs   = 3,
0384         /* .audio_inputs= 1, */
0385         .svhs       = 2,
0386         .gpiomask   = 7,
0387         .muxsel     = MUXSEL(2, 3, 1, 1),
0388         .gpiomux    = { 4, 0, 2, 3 },
0389         .gpiomute   = 1,
0390         .no_msp34xx = 1,
0391         .tuner_type     = TUNER_PHILIPS_NTSC,
0392         .tuner_addr = ADDR_UNSET,
0393         .pll            = PLL_28,
0394         .has_radio      = 1,
0395     },
0396 
0397     /* ---- card 0x04 ---------------------------------- */
0398     [BTTV_BOARD_INTEL] = {
0399         .name       = "Intel Create and Share PCI/ Smart Video Recorder III",
0400         .video_inputs   = 4,
0401         /* .audio_inputs= 0, */
0402         .svhs       = 2,
0403         .gpiomask   = 0,
0404         .muxsel     = MUXSEL(2, 3, 1, 1),
0405         .gpiomux    = { 0 },
0406         .tuner_type = TUNER_ABSENT,
0407         .tuner_addr = ADDR_UNSET,
0408     },
0409     [BTTV_BOARD_DIAMOND] = {
0410         .name       = "Diamond DTV2000",
0411         .video_inputs   = 4,
0412         /* .audio_inputs= 1, */
0413         .svhs       = 2,
0414         .gpiomask   = 3,
0415         .muxsel     = MUXSEL(2, 3, 1, 0),
0416         .gpiomux    = { 0, 1, 0, 1 },
0417         .gpiomute   = 3,
0418         .tuner_type = UNSET,
0419         .tuner_addr = ADDR_UNSET,
0420     },
0421     [BTTV_BOARD_AVERMEDIA] = {
0422         .name       = "AVerMedia TVPhone",
0423         .video_inputs   = 3,
0424         /* .audio_inputs= 1, */
0425         .svhs       = 3,
0426         .muxsel     = MUXSEL(2, 3, 1, 1),
0427         .gpiomask   = 0x0f,
0428         .gpiomux    = { 0x0c, 0x04, 0x08, 0x04 },
0429         /*                0x04 for some cards ?? */
0430         .tuner_type = UNSET,
0431         .tuner_addr = ADDR_UNSET,
0432         .audio_mode_gpio= avermedia_tvphone_audio,
0433         .has_remote     = 1,
0434     },
0435     [BTTV_BOARD_MATRIX_VISION] = {
0436         .name       = "MATRIX-Vision MV-Delta",
0437         .video_inputs   = 5,
0438         /* .audio_inputs= 1, */
0439         .svhs       = 3,
0440         .gpiomask   = 0,
0441         .muxsel     = MUXSEL(2, 3, 1, 0, 0),
0442         .gpiomux    = { 0 },
0443         .tuner_type = TUNER_ABSENT,
0444         .tuner_addr = ADDR_UNSET,
0445     },
0446 
0447     /* ---- card 0x08 ---------------------------------- */
0448     [BTTV_BOARD_FLYVIDEO] = {
0449         .name       = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26",
0450         .video_inputs   = 4,
0451         /* .audio_inputs= 1, */
0452         .svhs       = 2,
0453         .gpiomask   = 0xc00,
0454         .muxsel     = MUXSEL(2, 3, 1, 1),
0455         .gpiomux    = { 0, 0xc00, 0x800, 0x400 },
0456         .gpiomute   = 0xc00,
0457         .pll        = PLL_28,
0458         .tuner_type = UNSET,
0459         .tuner_addr = ADDR_UNSET,
0460     },
0461     [BTTV_BOARD_TURBOTV] = {
0462         .name       = "IMS/IXmicro TurboTV",
0463         .video_inputs   = 3,
0464         /* .audio_inputs= 1, */
0465         .svhs       = 2,
0466         .gpiomask   = 3,
0467         .muxsel     = MUXSEL(2, 3, 1, 1),
0468         .gpiomux    = { 1, 1, 2, 3 },
0469         .pll        = PLL_28,
0470         .tuner_type = TUNER_TEMIC_PAL,
0471         .tuner_addr = ADDR_UNSET,
0472     },
0473     [BTTV_BOARD_HAUPPAUGE878] = {
0474         .name       = "Hauppauge (bt878)",
0475         .video_inputs   = 4,
0476         /* .audio_inputs= 1, */
0477         .svhs       = 2,
0478         .gpiomask   = 0x0f, /* old: 7 */
0479         .muxsel     = MUXSEL(2, 0, 1, 1),
0480         .gpiomux    = { 0, 1, 2, 3 },
0481         .gpiomute   = 4,
0482         .pll        = PLL_28,
0483         .tuner_type = UNSET,
0484         .tuner_addr = ADDR_UNSET,
0485     },
0486     [BTTV_BOARD_MIROPRO] = {
0487         .name       = "MIRO PCTV pro",
0488         .video_inputs   = 3,
0489         /* .audio_inputs= 1, */
0490         .svhs       = 2,
0491         .gpiomask   = 0x3014f,
0492         .muxsel     = MUXSEL(2, 3, 1, 1),
0493         .gpiomux    = { 0x20001,0x10001, 0, 0 },
0494         .gpiomute   = 10,
0495         .tuner_type = UNSET,
0496         .tuner_addr = ADDR_UNSET,
0497     },
0498 
0499     /* ---- card 0x0c ---------------------------------- */
0500     [BTTV_BOARD_ADSTECH_TV] = {
0501         .name       = "ADS Technologies Channel Surfer TV (bt848)",
0502         .video_inputs   = 3,
0503         /* .audio_inputs= 1, */
0504         .svhs       = 2,
0505         .gpiomask   = 15,
0506         .muxsel     = MUXSEL(2, 3, 1, 1),
0507         .gpiomux    = { 13, 14, 11, 7 },
0508         .tuner_type = UNSET,
0509         .tuner_addr = ADDR_UNSET,
0510     },
0511     [BTTV_BOARD_AVERMEDIA98] = {
0512         .name       = "AVerMedia TVCapture 98",
0513         .video_inputs   = 3,
0514         /* .audio_inputs= 4, */
0515         .svhs       = 2,
0516         .gpiomask   = 15,
0517         .muxsel     = MUXSEL(2, 3, 1, 1),
0518         .gpiomux    = { 13, 14, 11, 7 },
0519         .msp34xx_alt    = 1,
0520         .pll        = PLL_28,
0521         .tuner_type = TUNER_PHILIPS_PAL,
0522         .tuner_addr = ADDR_UNSET,
0523         .audio_mode_gpio= avermedia_tv_stereo_audio,
0524         .no_gpioirq     = 1,
0525     },
0526     [BTTV_BOARD_VHX] = {
0527         .name       = "Aimslab Video Highway Xtreme (VHX)",
0528         .video_inputs   = 3,
0529         /* .audio_inputs= 1, */
0530         .svhs       = 2,
0531         .gpiomask   = 7,
0532         .muxsel     = MUXSEL(2, 3, 1, 1),
0533         .gpiomux    = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */
0534         .gpiomute   = 4,
0535         .pll        = PLL_28,
0536         .tuner_type = UNSET,
0537         .tuner_addr = ADDR_UNSET,
0538     },
0539     [BTTV_BOARD_ZOLTRIX] = {
0540         .name       = "Zoltrix TV-Max",
0541         .video_inputs   = 3,
0542         /* .audio_inputs= 1, */
0543         .svhs       = 2,
0544         .gpiomask   = 15,
0545         .muxsel     = MUXSEL(2, 3, 1, 1),
0546         .gpiomux    = { 0, 0, 1, 0 },
0547         .gpiomute   = 10,
0548         .tuner_type = UNSET,
0549         .tuner_addr = ADDR_UNSET,
0550     },
0551 
0552     /* ---- card 0x10 ---------------------------------- */
0553     [BTTV_BOARD_PIXVIEWPLAYTV] = {
0554         .name       = "Prolink Pixelview PlayTV (bt878)",
0555         .video_inputs   = 3,
0556         /* .audio_inputs= 1, */
0557         .svhs       = 2,
0558         .gpiomask   = 0x01fe00,
0559         .muxsel     = MUXSEL(2, 3, 1, 1),
0560         /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */
0561         .gpiomux        = { 0x001e00, 0, 0x018000, 0x014000 },
0562         .gpiomute   = 0x002000,
0563         .pll        = PLL_28,
0564         .tuner_type = UNSET,
0565         .tuner_addr     = ADDR_UNSET,
0566     },
0567     [BTTV_BOARD_WINVIEW_601] = {
0568         .name       = "Leadtek WinView 601",
0569         .video_inputs   = 3,
0570         /* .audio_inputs= 1, */
0571         .svhs       = 2,
0572         .gpiomask   = 0x8300f8,
0573         .muxsel     = MUXSEL(2, 3, 1, 1, 0),
0574         .gpiomux    = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 },
0575         .gpiomute   = 0xcfa007,
0576         .tuner_type = UNSET,
0577         .tuner_addr = ADDR_UNSET,
0578         .volume_gpio    = winview_volume,
0579         .has_radio  = 1,
0580     },
0581     [BTTV_BOARD_AVEC_INTERCAP] = {
0582         .name       = "AVEC Intercapture",
0583         .video_inputs   = 3,
0584         /* .audio_inputs= 2, */
0585         .svhs       = 2,
0586         .gpiomask   = 0,
0587         .muxsel     = MUXSEL(2, 3, 1, 1),
0588         .gpiomux    = { 1, 0, 0, 0 },
0589         .tuner_type = UNSET,
0590         .tuner_addr = ADDR_UNSET,
0591     },
0592     [BTTV_BOARD_LIFE_FLYKIT] = {
0593         .name       = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)",
0594         .video_inputs   = 4,
0595         /* .audio_inputs= 1, */
0596         .svhs       = NO_SVHS,
0597         .gpiomask   = 0x8dff00,
0598         .muxsel     = MUXSEL(2, 3, 1, 1),
0599         .gpiomux    = { 0 },
0600         .no_msp34xx = 1,
0601         .tuner_type = TUNER_ABSENT,
0602         .tuner_addr = ADDR_UNSET,
0603     },
0604 
0605     /* ---- card 0x14 ---------------------------------- */
0606     [BTTV_BOARD_CEI_RAFFLES] = {
0607         .name       = "CEI Raffles Card",
0608         .video_inputs   = 3,
0609         /* .audio_inputs= 3, */
0610         .svhs       = 2,
0611         .muxsel     = MUXSEL(2, 3, 1, 1),
0612         .tuner_type = UNSET,
0613         .tuner_addr = ADDR_UNSET,
0614     },
0615     [BTTV_BOARD_CONFERENCETV] = {
0616         .name       = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50",
0617         .video_inputs   = 4,
0618         /* .audio_inputs= 2,  tuner, line in */
0619         .svhs       = 2,
0620         .gpiomask   = 0x1800,
0621         .muxsel     = MUXSEL(2, 3, 1, 1),
0622         .gpiomux    = { 0, 0x800, 0x1000, 0x1000 },
0623         .gpiomute   = 0x1800,
0624         .pll        = PLL_28,
0625         .tuner_type = TUNER_PHILIPS_PAL_I,
0626         .tuner_addr = ADDR_UNSET,
0627     },
0628     [BTTV_BOARD_PHOEBE_TVMAS] = {
0629         .name       = "Askey CPH050/ Phoebe Tv Master + FM",
0630         .video_inputs   = 3,
0631         /* .audio_inputs= 1, */
0632         .svhs       = 2,
0633         .gpiomask   = 0xc00,
0634         .muxsel     = MUXSEL(2, 3, 1, 1),
0635         .gpiomux    = { 0, 1, 0x800, 0x400 },
0636         .gpiomute   = 0xc00,
0637         .pll        = PLL_28,
0638         .tuner_type = UNSET,
0639         .tuner_addr = ADDR_UNSET,
0640     },
0641     [BTTV_BOARD_MODTEC_205] = {
0642         .name       = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878",
0643         .video_inputs   = 3,
0644         /* .audio_inputs= 1, */
0645         .svhs       = NO_SVHS,
0646         .has_dig_in = 1,
0647         .gpiomask   = 7,
0648         .muxsel     = MUXSEL(2, 3, 0), /* input 2 is digital */
0649         /* .digital_mode= DIGITAL_MODE_CAMERA, */
0650         .gpiomux    = { 0, 0, 0, 0 },
0651         .no_msp34xx = 1,
0652         .pll            = PLL_28,
0653         .tuner_type     = TUNER_ALPS_TSBB5_PAL_I,
0654         .tuner_addr = ADDR_UNSET,
0655     },
0656 
0657     /* ---- card 0x18 ---------------------------------- */
0658     [BTTV_BOARD_MAGICTVIEW061] = {
0659         .name       = "Askey CPH05X/06X (bt878) [many vendors]",
0660         .video_inputs   = 3,
0661         /* .audio_inputs= 1, */
0662         .svhs       = 2,
0663         .gpiomask   = 0xe00,
0664         .muxsel     = MUXSEL(2, 3, 1, 1),
0665         .gpiomux    = {0x400, 0x400, 0x400, 0x400 },
0666         .gpiomute   = 0xc00,
0667         .pll        = PLL_28,
0668         .tuner_type = UNSET,
0669         .tuner_addr = ADDR_UNSET,
0670         .has_remote     = 1,
0671         .has_radio  = 1,  /* not every card has radio */
0672     },
0673     [BTTV_BOARD_VOBIS_BOOSTAR] = {
0674         .name           = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar",
0675         .video_inputs   = 3,
0676         /* .audio_inputs= 1, */
0677         .svhs       = 2,
0678         .gpiomask       = 0x1f0fff,
0679         .muxsel     = MUXSEL(2, 3, 1, 1),
0680         .gpiomux        = { 0x20000, 0x30000, 0x10000, 0 },
0681         .gpiomute   = 0x40000,
0682         .tuner_type = TUNER_PHILIPS_PAL,
0683         .tuner_addr = ADDR_UNSET,
0684         .audio_mode_gpio= terratv_audio,
0685     },
0686     [BTTV_BOARD_HAUPPAUG_WCAM] = {
0687         .name       = "Hauppauge WinCam newer (bt878)",
0688         .video_inputs   = 4,
0689         /* .audio_inputs= 1, */
0690         .svhs       = 3,
0691         .gpiomask   = 7,
0692         .muxsel     = MUXSEL(2, 0, 1, 1),
0693         .gpiomux    = { 0, 1, 2, 3 },
0694         .gpiomute   = 4,
0695         .tuner_type = UNSET,
0696         .tuner_addr = ADDR_UNSET,
0697     },
0698     [BTTV_BOARD_MAXI] = {
0699         .name       = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50",
0700         .video_inputs   = 4,
0701         /* .audio_inputs= 2, */
0702         .svhs       = 2,
0703         .gpiomask   = 0x1800,
0704         .muxsel     = MUXSEL(2, 3, 1, 1),
0705         .gpiomux    = { 0, 0x800, 0x1000, 0x1000 },
0706         .gpiomute   = 0x1800,
0707         .pll            = PLL_28,
0708         .tuner_type = TUNER_PHILIPS_SECAM,
0709         .tuner_addr = ADDR_UNSET,
0710     },
0711 
0712     /* ---- card 0x1c ---------------------------------- */
0713     [BTTV_BOARD_TERRATV] = {
0714         .name           = "Terratec TerraTV+ Version 1.1 (bt878)",
0715         .video_inputs   = 3,
0716         /* .audio_inputs= 1, */
0717         .svhs       = 2,
0718         .gpiomask   = 0x1f0fff,
0719         .muxsel     = MUXSEL(2, 3, 1, 1),
0720         .gpiomux    = { 0x20000, 0x30000, 0x10000, 0x00000 },
0721         .gpiomute   = 0x40000,
0722         .tuner_type = TUNER_PHILIPS_PAL,
0723         .tuner_addr = ADDR_UNSET,
0724         .audio_mode_gpio= terratv_audio,
0725         /* GPIO wiring:
0726         External 20 pin connector (for Active Radio Upgrade board)
0727         gpio00: i2c-sda
0728         gpio01: i2c-scl
0729         gpio02: om5610-data
0730         gpio03: om5610-clk
0731         gpio04: om5610-wre
0732         gpio05: om5610-stereo
0733         gpio06: rds6588-davn
0734         gpio07: Pin 7 n.c.
0735         gpio08: nIOW
0736         gpio09+10: nIOR, nSEL ?? (bt878)
0737             gpio09: nIOR (bt848)
0738             gpio10: nSEL (bt848)
0739         Sound Routing:
0740         gpio16: u2-A0 (1st 4052bt)
0741         gpio17: u2-A1
0742         gpio18: u2-nEN
0743         gpio19: u4-A0 (2nd 4052)
0744         gpio20: u4-A1
0745             u4-nEN - GND
0746         Btspy:
0747             00000 : Cdrom (internal audio input)
0748             10000 : ext. Video audio input
0749             20000 : TV Mono
0750             a0000 : TV Mono/2
0751         1a0000 : TV Stereo
0752             30000 : Radio
0753             40000 : Mute
0754     */
0755 
0756     },
0757     [BTTV_BOARD_PXC200] = {
0758         /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */
0759         .name       = "Imagenation PXC200",
0760         .video_inputs   = 5,
0761         /* .audio_inputs= 1, */
0762         .svhs       = 1, /* was: 4 */
0763         .gpiomask   = 0,
0764         .muxsel     = MUXSEL(2, 3, 1, 0, 0),
0765         .gpiomux    = { 0 },
0766         .tuner_type = TUNER_ABSENT,
0767         .tuner_addr = ADDR_UNSET,
0768         .muxsel_hook    = PXC200_muxsel,
0769 
0770     },
0771     [BTTV_BOARD_FLYVIDEO_98] = {
0772         .name       = "Lifeview FlyVideo 98 LR50",
0773         .video_inputs   = 4,
0774         /* .audio_inputs= 1, */
0775         .svhs       = 2,
0776         .gpiomask   = 0x1800,  /* 0x8dfe00 */
0777         .muxsel     = MUXSEL(2, 3, 1, 1),
0778         .gpiomux    = { 0, 0x0800, 0x1000, 0x1000 },
0779         .gpiomute   = 0x1800,
0780         .pll            = PLL_28,
0781         .tuner_type = UNSET,
0782         .tuner_addr = ADDR_UNSET,
0783     },
0784     [BTTV_BOARD_IPROTV] = {
0785         .name       = "Formac iProTV, Formac ProTV I (bt848)",
0786         .video_inputs   = 4,
0787         /* .audio_inputs= 1, */
0788         .svhs       = 3,
0789         .gpiomask   = 1,
0790         .muxsel     = MUXSEL(2, 3, 1, 1),
0791         .gpiomux    = { 1, 0, 0, 0 },
0792         .pll            = PLL_28,
0793         .tuner_type = TUNER_PHILIPS_PAL,
0794         .tuner_addr = ADDR_UNSET,
0795     },
0796 
0797     /* ---- card 0x20 ---------------------------------- */
0798     [BTTV_BOARD_INTEL_C_S_PCI] = {
0799         .name       = "Intel Create and Share PCI/ Smart Video Recorder III",
0800         .video_inputs   = 4,
0801         /* .audio_inputs= 0, */
0802         .svhs       = 2,
0803         .gpiomask   = 0,
0804         .muxsel     = MUXSEL(2, 3, 1, 1),
0805         .gpiomux    = { 0 },
0806         .tuner_type = TUNER_ABSENT,
0807         .tuner_addr = ADDR_UNSET,
0808     },
0809     [BTTV_BOARD_TERRATVALUE] = {
0810         .name           = "Terratec TerraTValue Version Bt878",
0811         .video_inputs   = 3,
0812         /* .audio_inputs= 1, */
0813         .svhs       = 2,
0814         .gpiomask   = 0xffff00,
0815         .muxsel     = MUXSEL(2, 3, 1, 1),
0816         .gpiomux    = { 0x500, 0, 0x300, 0x900 },
0817         .gpiomute   = 0x900,
0818         .pll        = PLL_28,
0819         .tuner_type = TUNER_PHILIPS_PAL,
0820         .tuner_addr = ADDR_UNSET,
0821     },
0822     [BTTV_BOARD_WINFAST2000] = {
0823         .name       = "Leadtek WinFast 2000/ WinFast 2000 XP",
0824         .video_inputs   = 4,
0825         /* .audio_inputs= 1, */
0826         .svhs       = 2,
0827         /* TV, CVid, SVid, CVid over SVid connector */
0828         .muxsel     = MUXSEL(2, 3, 1, 1, 0),
0829         /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */
0830         .gpiomask   = 0xb33000,
0831         .gpiomux    = { 0x122000,0x1000,0x0000,0x620000 },
0832         .gpiomute   = 0x800000,
0833         /* Audio Routing for "WinFast 2000 XP" (no tv stereo !)
0834             gpio23 -- hef4052:nEnable (0x800000)
0835             gpio12 -- hef4052:A1
0836             gpio13 -- hef4052:A0
0837         0x0000: external audio
0838         0x1000: FM
0839         0x2000: TV
0840         0x3000: n.c.
0841         Note: There exists another variant "Winfast 2000" with tv stereo !?
0842         Note: eeprom only contains FF and pci subsystem id 107d:6606
0843         */
0844         .pll        = PLL_28,
0845         .has_radio  = 1,
0846         .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */
0847         .tuner_addr = ADDR_UNSET,
0848         .audio_mode_gpio= winfast2000_audio,
0849         .has_remote     = 1,
0850     },
0851     [BTTV_BOARD_CHRONOS_VS2] = {
0852         .name       = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II",
0853         .video_inputs   = 4,
0854         /* .audio_inputs= 3, */
0855         .svhs       = 2,
0856         .gpiomask   = 0x1800,
0857         .muxsel     = MUXSEL(2, 3, 1, 1),
0858         .gpiomux    = { 0, 0x800, 0x1000, 0x1000 },
0859         .gpiomute   = 0x1800,
0860         .pll        = PLL_28,
0861         .tuner_type = UNSET,
0862         .tuner_addr = ADDR_UNSET,
0863     },
0864 
0865     /* ---- card 0x24 ---------------------------------- */
0866     [BTTV_BOARD_TYPHOON_TVIEW] = {
0867         .name       = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner",
0868         .video_inputs   = 4,
0869         /* .audio_inputs= 3, */
0870         .svhs       = 2,
0871         .gpiomask   = 0x1800,
0872         .muxsel     = MUXSEL(2, 3, 1, 1),
0873         .gpiomux    = { 0, 0x800, 0x1000, 0x1000 },
0874         .gpiomute   = 0x1800,
0875         .pll        = PLL_28,
0876         .tuner_type = UNSET,
0877         .tuner_addr = ADDR_UNSET,
0878         .has_radio  = 1,
0879     },
0880     [BTTV_BOARD_PXELVWPLTVPRO] = {
0881         .name       = "Prolink PixelView PlayTV pro",
0882         .video_inputs   = 3,
0883         /* .audio_inputs= 1, */
0884         .svhs       = 2,
0885         .gpiomask   = 0xff,
0886         .muxsel     = MUXSEL(2, 3, 1, 1),
0887         .gpiomux    = { 0x21, 0x20, 0x24, 0x2c },
0888         .gpiomute   = 0x29,
0889         .no_msp34xx = 1,
0890         .pll        = PLL_28,
0891         .tuner_type = UNSET,
0892         .tuner_addr = ADDR_UNSET,
0893     },
0894     [BTTV_BOARD_MAGICTVIEW063] = {
0895         .name       = "Askey CPH06X TView99",
0896         .video_inputs   = 4,
0897         /* .audio_inputs= 1, */
0898         .svhs       = 2,
0899         .gpiomask   = 0x551e00,
0900         .muxsel     = MUXSEL(2, 3, 1, 0),
0901         .gpiomux    = { 0x551400, 0x551200, 0, 0 },
0902         .gpiomute   = 0x551c00,
0903         .pll        = PLL_28,
0904         .tuner_type = TUNER_PHILIPS_PAL_I,
0905         .tuner_addr = ADDR_UNSET,
0906         .has_remote     = 1,
0907     },
0908     [BTTV_BOARD_PINNACLE] = {
0909         .name       = "Pinnacle PCTV Studio/Rave",
0910         .video_inputs   = 3,
0911         /* .audio_inputs= 1, */
0912         .svhs       = 2,
0913         .gpiomask   = 0x03000F,
0914         .muxsel     = MUXSEL(2, 3, 1, 1),
0915         .gpiomux    = { 2, 0xd0001, 0, 0 },
0916         .gpiomute   = 1,
0917         .pll        = PLL_28,
0918         .tuner_type = UNSET,
0919         .tuner_addr = ADDR_UNSET,
0920     },
0921 
0922     /* ---- card 0x28 ---------------------------------- */
0923     [BTTV_BOARD_STB2] = {
0924         .name       = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100",
0925         .video_inputs   = 3,
0926         /* .audio_inputs= 1, */
0927         .svhs       = 2,
0928         .gpiomask   = 7,
0929         .muxsel     = MUXSEL(2, 3, 1, 1),
0930         .gpiomux    = { 4, 0, 2, 3 },
0931         .gpiomute   = 1,
0932         .no_msp34xx = 1,
0933         .tuner_type     = TUNER_PHILIPS_NTSC,
0934         .tuner_addr = ADDR_UNSET,
0935         .pll            = PLL_28,
0936         .has_radio      = 1,
0937     },
0938     [BTTV_BOARD_AVPHONE98] = {
0939         .name       = "AVerMedia TVPhone 98",
0940         .video_inputs   = 3,
0941         /* .audio_inputs= 4, */
0942         .svhs       = 2,
0943         .gpiomask   = 15,
0944         .muxsel     = MUXSEL(2, 3, 1, 1),
0945         .gpiomux    = { 13, 4, 11, 7 },
0946         .pll        = PLL_28,
0947         .tuner_type = UNSET,
0948         .tuner_addr = ADDR_UNSET,
0949         .has_radio  = 1,
0950         .audio_mode_gpio= avermedia_tvphone_audio,
0951     },
0952     [BTTV_BOARD_PV951] = {
0953         .name       = "ProVideo PV951", /* pic16c54 */
0954         .video_inputs   = 3,
0955         /* .audio_inputs= 1, */
0956         .svhs       = 2,
0957         .gpiomask   = 0,
0958         .muxsel     = MUXSEL(2, 3, 1, 1),
0959         .gpiomux    = { 0, 0, 0, 0},
0960         .no_msp34xx = 1,
0961         .pll        = PLL_28,
0962         .tuner_type = TUNER_PHILIPS_PAL_I,
0963         .tuner_addr = ADDR_UNSET,
0964     },
0965     [BTTV_BOARD_ONAIR_TV] = {
0966         .name       = "Little OnAir TV",
0967         .video_inputs   = 3,
0968         /* .audio_inputs= 1, */
0969         .svhs       = 2,
0970         .gpiomask   = 0xe00b,
0971         .muxsel     = MUXSEL(2, 3, 1, 1),
0972         .gpiomux    = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 },
0973         .gpiomute   = 0xff3ffc,
0974         .no_msp34xx = 1,
0975         .tuner_type = UNSET,
0976         .tuner_addr = ADDR_UNSET,
0977     },
0978 
0979     /* ---- card 0x2c ---------------------------------- */
0980     [BTTV_BOARD_SIGMA_TVII_FM] = {
0981         .name       = "Sigma TVII-FM",
0982         .video_inputs   = 2,
0983         /* .audio_inputs= 1, */
0984         .svhs       = NO_SVHS,
0985         .gpiomask   = 3,
0986         .muxsel     = MUXSEL(2, 3, 1, 1),
0987         .gpiomux    = { 1, 1, 0, 2 },
0988         .gpiomute   = 3,
0989         .no_msp34xx = 1,
0990         .pll        = PLL_NONE,
0991         .tuner_type = UNSET,
0992         .tuner_addr = ADDR_UNSET,
0993     },
0994     [BTTV_BOARD_MATRIX_VISION2] = {
0995         .name       = "MATRIX-Vision MV-Delta 2",
0996         .video_inputs   = 5,
0997         /* .audio_inputs= 1, */
0998         .svhs       = 3,
0999         .gpiomask   = 0,
1000         .muxsel     = MUXSEL(2, 3, 1, 0, 0),
1001         .gpiomux    = { 0 },
1002         .no_msp34xx = 1,
1003         .pll        = PLL_28,
1004         .tuner_type = TUNER_ABSENT,
1005         .tuner_addr = ADDR_UNSET,
1006     },
1007     [BTTV_BOARD_ZOLTRIX_GENIE] = {
1008         .name       = "Zoltrix Genie TV/FM",
1009         .video_inputs   = 3,
1010         /* .audio_inputs= 1, */
1011         .svhs       = 2,
1012         .gpiomask   = 0xbcf03f,
1013         .muxsel     = MUXSEL(2, 3, 1, 1),
1014         .gpiomux    = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 },
1015         .gpiomute   = 0xbcb03f,
1016         .no_msp34xx = 1,
1017         .pll        = PLL_28,
1018         .tuner_type = TUNER_TEMIC_4039FR5_NTSC,
1019         .tuner_addr = ADDR_UNSET,
1020     },
1021     [BTTV_BOARD_TERRATVRADIO] = {
1022         .name       = "Terratec TV/Radio+",
1023         .video_inputs   = 3,
1024         /* .audio_inputs= 1, */
1025         .svhs       = 2,
1026         .gpiomask   = 0x70000,
1027         .muxsel     = MUXSEL(2, 3, 1, 1),
1028         .gpiomux    = { 0x20000, 0x30000, 0x10000, 0 },
1029         .gpiomute   = 0x40000,
1030         .no_msp34xx = 1,
1031         .pll        = PLL_35,
1032         .tuner_type = TUNER_PHILIPS_PAL_I,
1033         .tuner_addr = ADDR_UNSET,
1034         .has_radio  = 1,
1035     },
1036 
1037     /* ---- card 0x30 ---------------------------------- */
1038     [BTTV_BOARD_DYNALINK] = {
1039         .name       = "Askey CPH03x/ Dynalink Magic TView",
1040         .video_inputs   = 3,
1041         /* .audio_inputs= 1, */
1042         .svhs       = 2,
1043         .gpiomask   = 15,
1044         .muxsel     = MUXSEL(2, 3, 1, 1),
1045         .gpiomux    = {2,0,0,0 },
1046         .gpiomute   = 1,
1047         .pll        = PLL_28,
1048         .tuner_type = UNSET,
1049         .tuner_addr = ADDR_UNSET,
1050     },
1051     [BTTV_BOARD_GVBCTV3PCI] = {
1052         .name       = "IODATA GV-BCTV3/PCI",
1053         .video_inputs   = 3,
1054         /* .audio_inputs= 1, */
1055         .svhs       = 2,
1056         .gpiomask   = 0x010f00,
1057         .muxsel     = MUXSEL(2, 3, 0, 0),
1058         .gpiomux    = {0x10000, 0, 0x10000, 0 },
1059         .no_msp34xx = 1,
1060         .pll        = PLL_28,
1061         .tuner_type = TUNER_ALPS_TSHC6_NTSC,
1062         .tuner_addr = ADDR_UNSET,
1063         .audio_mode_gpio= gvbctv3pci_audio,
1064     },
1065     [BTTV_BOARD_PXELVWPLTVPAK] = {
1066         .name       = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP",
1067         .video_inputs   = 5,
1068         /* .audio_inputs= 1, */
1069         .svhs       = 3,
1070         .has_dig_in = 1,
1071         .gpiomask   = 0xAA0000,
1072         .muxsel     = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */
1073         /* .digital_mode= DIGITAL_MODE_CAMERA, */
1074         .gpiomux    = { 0x20000, 0, 0x80000, 0x80000 },
1075         .gpiomute   = 0xa8000,
1076         .no_msp34xx = 1,
1077         .pll        = PLL_28,
1078         .tuner_type = TUNER_PHILIPS_PAL_I,
1079         .tuner_addr = ADDR_UNSET,
1080         .has_remote = 1,
1081         /* GPIO wiring: (different from Rev.4C !)
1082             GPIO17: U4.A0 (first hef4052bt)
1083             GPIO19: U4.A1
1084             GPIO20: U5.A1 (second hef4052bt)
1085             GPIO21: U4.nEN
1086             GPIO22: BT832 Reset Line
1087             GPIO23: A5,A0, U5,nEN
1088         Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22
1089         */
1090     },
1091     [BTTV_BOARD_EAGLE] = {
1092         .name           = "Eagle Wireless Capricorn2 (bt878A)",
1093         .video_inputs   = 4,
1094         /* .audio_inputs= 1, */
1095         .svhs           = 2,
1096         .gpiomask       = 7,
1097         .muxsel         = MUXSEL(2, 0, 1, 1),
1098         .gpiomux        = { 0, 1, 2, 3 },
1099         .gpiomute   = 4,
1100         .pll            = PLL_28,
1101         .tuner_type     = UNSET /* TUNER_ALPS_TMDH2_NTSC */,
1102         .tuner_addr = ADDR_UNSET,
1103     },
1104 
1105     /* ---- card 0x34 ---------------------------------- */
1106     [BTTV_BOARD_PINNACLEPRO] = {
1107         /* David Härdeman <david@2gen.com> */
1108         .name           = "Pinnacle PCTV Studio Pro",
1109         .video_inputs   = 4,
1110         /* .audio_inputs= 1, */
1111         .svhs           = 3,
1112         .gpiomask       = 0x03000F,
1113         .muxsel     = MUXSEL(2, 3, 1, 1),
1114         .gpiomux    = { 1, 0xd0001, 0, 0 },
1115         .gpiomute   = 10,
1116                 /* sound path (5 sources):
1117                 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable)
1118                     0= ext. Audio IN
1119                     1= from MUX2
1120                     2= Mono TV sound from Tuner
1121                     3= not connected
1122                 MUX2 (mask 0x30000):
1123                     0,2,3= from MSP34xx
1124                     1= FM stereo Radio from Tuner */
1125         .pll            = PLL_28,
1126         .tuner_type     = UNSET,
1127         .tuner_addr = ADDR_UNSET,
1128     },
1129     [BTTV_BOARD_TVIEW_RDS_FM] = {
1130         /* Claas Langbehn <claas@bigfoot.com>,
1131         Sven Grothklags <sven@upb.de> */
1132         .name       = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS",
1133         .video_inputs   = 4,
1134         /* .audio_inputs= 3, */
1135         .svhs       = 2,
1136         .gpiomask   = 0x1c,
1137         .muxsel     = MUXSEL(2, 3, 1, 1),
1138         .gpiomux    = { 0, 0, 0x10, 8 },
1139         .gpiomute   = 4,
1140         .pll        = PLL_28,
1141         .tuner_type = TUNER_PHILIPS_PAL,
1142         .tuner_addr = ADDR_UNSET,
1143         .has_radio  = 1,
1144     },
1145     [BTTV_BOARD_LIFETEC_9415] = {
1146         /* Tim Röstermundt <rosterm@uni-muenster.de>
1147         in de.comp.os.unix.linux.hardware:
1148             options bttv card=0 pll=1 radio=1 gpiomask=0x18e0
1149             gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff
1150             options tuner type=5 */
1151         .name       = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]",
1152         .video_inputs   = 4,
1153         /* .audio_inputs= 1, */
1154         .svhs       = 2,
1155         .gpiomask   = 0x18e0,
1156         .muxsel     = MUXSEL(2, 3, 1, 1),
1157         .gpiomux    = { 0x0000,0x0800,0x1000,0x1000 },
1158         .gpiomute   = 0x18e0,
1159             /* For cards with tda9820/tda9821:
1160                 0x0000: Tuner normal stereo
1161                 0x0080: Tuner A2 SAP (second audio program = Zweikanalton)
1162                 0x0880: Tuner A2 stereo */
1163         .pll        = PLL_28,
1164         .tuner_type = UNSET,
1165         .tuner_addr = ADDR_UNSET,
1166     },
1167     [BTTV_BOARD_BESTBUY_EASYTV] = {
1168         /* Miguel Angel Alvarez <maacruz@navegalia.com>
1169         old Easy TV BT848 version (model CPH031) */
1170         .name           = "Askey CPH031/ BESTBUY Easy TV",
1171         .video_inputs   = 4,
1172         /* .audio_inputs= 1, */
1173         .svhs           = 2,
1174         .gpiomask       = 0xF,
1175         .muxsel         = MUXSEL(2, 3, 1, 0),
1176         .gpiomux        = { 2, 0, 0, 0 },
1177         .gpiomute   = 10,
1178         .pll        = PLL_28,
1179         .tuner_type = TUNER_TEMIC_PAL,
1180         .tuner_addr = ADDR_UNSET,
1181     },
1182 
1183     /* ---- card 0x38 ---------------------------------- */
1184     [BTTV_BOARD_FLYVIDEO_98FM] = {
1185         /* Gordon Heydon <gjheydon@bigfoot.com ('98) */
1186         .name           = "Lifeview FlyVideo 98FM LR50",
1187         .video_inputs   = 4,
1188         /* .audio_inputs= 3, */
1189         .svhs           = 2,
1190         .gpiomask       = 0x1800,
1191         .muxsel         = MUXSEL(2, 3, 1, 1),
1192         .gpiomux        = { 0, 0x800, 0x1000, 0x1000 },
1193         .gpiomute   = 0x1800,
1194         .pll            = PLL_28,
1195         .tuner_type     = TUNER_PHILIPS_PAL,
1196         .tuner_addr = ADDR_UNSET,
1197     },
1198         /* This is the ultimate cheapo capture card
1199         * just a BT848A on a small PCB!
1200         * Steve Hosgood <steve@equiinet.com> */
1201     [BTTV_BOARD_GRANDTEC] = {
1202         .name           = "GrandTec 'Grand Video Capture' (Bt848)",
1203         .video_inputs   = 2,
1204         /* .audio_inputs= 0, */
1205         .svhs           = 1,
1206         .gpiomask       = 0,
1207         .muxsel         = MUXSEL(3, 1),
1208         .gpiomux        = { 0 },
1209         .no_msp34xx     = 1,
1210         .pll            = PLL_35,
1211         .tuner_type     = TUNER_ABSENT,
1212         .tuner_addr = ADDR_UNSET,
1213     },
1214     [BTTV_BOARD_ASKEY_CPH060] = {
1215         /* Daniel Herrington <daniel.herrington@home.com> */
1216         .name           = "Askey CPH060/ Phoebe TV Master Only (No FM)",
1217         .video_inputs   = 3,
1218         /* .audio_inputs= 1, */
1219         .svhs           = 2,
1220         .gpiomask       = 0xe00,
1221         .muxsel         = MUXSEL(2, 3, 1, 1),
1222         .gpiomux        = { 0x400, 0x400, 0x400, 0x400 },
1223         .gpiomute   = 0x800,
1224         .pll            = PLL_28,
1225         .tuner_type     = TUNER_TEMIC_4036FY5_NTSC,
1226         .tuner_addr = ADDR_UNSET,
1227     },
1228     [BTTV_BOARD_ASKEY_CPH03X] = {
1229         /* Matti Mottus <mottus@physic.ut.ee> */
1230         .name       = "Askey CPH03x TV Capturer",
1231         .video_inputs   = 4,
1232         /* .audio_inputs= 1, */
1233         .svhs       = 2,
1234         .gpiomask       = 0x03000F,
1235         .muxsel     = MUXSEL(2, 3, 1, 0),
1236         .gpiomux        = { 2, 0, 0, 0 },
1237         .gpiomute   = 1,
1238         .pll            = PLL_28,
1239         .tuner_type = TUNER_TEMIC_PAL,
1240         .tuner_addr = ADDR_UNSET,
1241         .has_remote = 1,
1242     },
1243 
1244     /* ---- card 0x3c ---------------------------------- */
1245     [BTTV_BOARD_MM100PCTV] = {
1246         /* Philip Blundell <philb@gnu.org> */
1247         .name           = "Modular Technology MM100PCTV",
1248         .video_inputs   = 2,
1249         /* .audio_inputs= 2, */
1250         .svhs       = NO_SVHS,
1251         .gpiomask       = 11,
1252         .muxsel         = MUXSEL(2, 3, 1, 1),
1253         .gpiomux        = { 2, 0, 0, 1 },
1254         .gpiomute   = 8,
1255         .pll            = PLL_35,
1256         .tuner_type     = TUNER_TEMIC_PAL,
1257         .tuner_addr = ADDR_UNSET,
1258     },
1259     [BTTV_BOARD_GMV1] = {
1260         /* Adrian Cox <adrian@humboldt.co.uk */
1261         .name       = "AG Electronics GMV1",
1262         .video_inputs   = 2,
1263         /* .audio_inputs= 0, */
1264         .svhs       = 1,
1265         .gpiomask       = 0xF,
1266         .muxsel     = MUXSEL(2, 2),
1267         .gpiomux        = { },
1268         .no_msp34xx     = 1,
1269         .pll        = PLL_28,
1270         .tuner_type     = TUNER_ABSENT,
1271         .tuner_addr = ADDR_UNSET,
1272     },
1273     [BTTV_BOARD_BESTBUY_EASYTV2] = {
1274         /* Miguel Angel Alvarez <maacruz@navegalia.com>
1275         new Easy TV BT878 version (model CPH061)
1276         special thanks to Informatica Mieres for providing the card */
1277         .name           = "Askey CPH061/ BESTBUY Easy TV (bt878)",
1278         .video_inputs   = 3,
1279         /* .audio_inputs= 2, */
1280         .svhs           = 2,
1281         .gpiomask       = 0xFF,
1282         .muxsel         = MUXSEL(2, 3, 1, 0),
1283         .gpiomux        = { 1, 0, 4, 4 },
1284         .gpiomute   = 9,
1285         .pll        = PLL_28,
1286         .tuner_type = TUNER_PHILIPS_PAL,
1287         .tuner_addr = ADDR_UNSET,
1288     },
1289     [BTTV_BOARD_ATI_TVWONDER] = {
1290         /* Lukas Gebauer <geby@volny.cz> */
1291         .name       = "ATI TV-Wonder",
1292         .video_inputs   = 3,
1293         /* .audio_inputs= 1, */
1294         .svhs       = 2,
1295         .gpiomask   = 0xf03f,
1296         .muxsel     = MUXSEL(2, 3, 1, 0),
1297         .gpiomux    = { 0xbffe, 0, 0xbfff, 0 },
1298         .gpiomute   = 0xbffe,
1299         .pll        = PLL_28,
1300         .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1301         .tuner_addr = ADDR_UNSET,
1302     },
1303 
1304     /* ---- card 0x40 ---------------------------------- */
1305     [BTTV_BOARD_ATI_TVWONDERVE] = {
1306         /* Lukas Gebauer <geby@volny.cz> */
1307         .name       = "ATI TV-Wonder VE",
1308         .video_inputs   = 2,
1309         /* .audio_inputs= 1, */
1310         .svhs       = NO_SVHS,
1311         .gpiomask   = 1,
1312         .muxsel     = MUXSEL(2, 3, 0, 1),
1313         .gpiomux    = { 0, 0, 1, 0 },
1314         .no_msp34xx = 1,
1315         .pll        = PLL_28,
1316         .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1317         .tuner_addr = ADDR_UNSET,
1318     },
1319     [BTTV_BOARD_FLYVIDEO2000] = {
1320         /* DeeJay <deejay@westel900.net (2000S) */
1321         .name           = "Lifeview FlyVideo 2000S LR90",
1322         .video_inputs   = 3,
1323         /* .audio_inputs= 3, */
1324         .svhs           = 2,
1325         .gpiomask   = 0x18e0,
1326         .muxsel     = MUXSEL(2, 3, 0, 1),
1327                 /* Radio changed from 1e80 to 0x800 to make
1328                 FlyVideo2000S in .hu happy (gm)*/
1329                 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */
1330         .gpiomux    = { 0x0000,0x0800,0x1000,0x1000 },
1331         .gpiomute   = 0x1800,
1332         .audio_mode_gpio= fv2000s_audio,
1333         .no_msp34xx = 1,
1334         .pll            = PLL_28,
1335         .tuner_type     = TUNER_PHILIPS_PAL,
1336         .tuner_addr = ADDR_UNSET,
1337     },
1338     [BTTV_BOARD_TERRATVALUER] = {
1339         .name       = "Terratec TValueRadio",
1340         .video_inputs   = 3,
1341         /* .audio_inputs= 1, */
1342         .svhs       = 2,
1343         .gpiomask   = 0xffff00,
1344         .muxsel     = MUXSEL(2, 3, 1, 1),
1345         .gpiomux    = { 0x500, 0x500, 0x300, 0x900 },
1346         .gpiomute   = 0x900,
1347         .pll        = PLL_28,
1348         .tuner_type = TUNER_PHILIPS_PAL,
1349         .tuner_addr = ADDR_UNSET,
1350         .has_radio  = 1,
1351     },
1352     [BTTV_BOARD_GVBCTV4PCI] = {
1353         /* TANAKA Kei <peg00625@nifty.com> */
1354         .name           = "IODATA GV-BCTV4/PCI",
1355         .video_inputs   = 3,
1356         /* .audio_inputs= 1, */
1357         .svhs           = 2,
1358         .gpiomask       = 0x010f00,
1359         .muxsel         = MUXSEL(2, 3, 0, 0),
1360         .gpiomux        = {0x10000, 0, 0x10000, 0 },
1361         .no_msp34xx     = 1,
1362         .pll            = PLL_28,
1363         .tuner_type     = TUNER_SHARP_2U5JF5540_NTSC,
1364         .tuner_addr = ADDR_UNSET,
1365         .audio_mode_gpio= gvbctv3pci_audio,
1366     },
1367 
1368     /* ---- card 0x44 ---------------------------------- */
1369     [BTTV_BOARD_VOODOOTV_FM] = {
1370         .name           = "3Dfx VoodooTV FM (Euro)",
1371         /* try "insmod msp3400 simple=0" if you have
1372         * sound problems with this card. */
1373         .video_inputs   = 4,
1374         /* .audio_inputs= 1, */
1375         .svhs           = NO_SVHS,
1376         .gpiomask       = 0x4f8a00,
1377         /* 0x100000: 1=MSP enabled (0=disable again)
1378         * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1379         .gpiomux        = {0x947fff, 0x987fff,0x947fff,0x947fff },
1380         .gpiomute   = 0x947fff,
1381         /* tvtuner, radio,   external,internal, mute,  stereo
1382         * tuner, Composite, SVid, Composite-on-Svid-adapter */
1383         .muxsel         = MUXSEL(2, 3, 0, 1),
1384         .tuner_type     = TUNER_MT2032,
1385         .tuner_addr = ADDR_UNSET,
1386         .pll        = PLL_28,
1387         .has_radio  = 1,
1388     },
1389     [BTTV_BOARD_VOODOOTV_200] = {
1390         .name           = "VoodooTV 200 (USA)",
1391         /* try "insmod msp3400 simple=0" if you have
1392         * sound problems with this card. */
1393         .video_inputs   = 4,
1394         /* .audio_inputs= 1, */
1395         .svhs           = NO_SVHS,
1396         .gpiomask       = 0x4f8a00,
1397         /* 0x100000: 1=MSP enabled (0=disable again)
1398         * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1399         .gpiomux        = {0x947fff, 0x987fff,0x947fff,0x947fff },
1400         .gpiomute   = 0x947fff,
1401         /* tvtuner, radio,   external,internal, mute,  stereo
1402         * tuner, Composite, SVid, Composite-on-Svid-adapter */
1403         .muxsel         = MUXSEL(2, 3, 0, 1),
1404         .tuner_type     = TUNER_MT2032,
1405         .tuner_addr = ADDR_UNSET,
1406         .pll        = PLL_28,
1407         .has_radio  = 1,
1408     },
1409     [BTTV_BOARD_AIMMS] = {
1410         /* Philip Blundell <pb@nexus.co.uk> */
1411         .name           = "Active Imaging AIMMS",
1412         .video_inputs   = 1,
1413         /* .audio_inputs= 0, */
1414         .tuner_type     = TUNER_ABSENT,
1415         .tuner_addr = ADDR_UNSET,
1416         .pll            = PLL_28,
1417         .muxsel         = MUXSEL(2),
1418         .gpiomask       = 0
1419     },
1420     [BTTV_BOARD_PV_BT878P_PLUS] = {
1421         /* Tomasz Pyra <hellfire@sedez.iq.pl> */
1422         .name           = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)",
1423         .video_inputs   = 3,
1424         /* .audio_inputs= 4, */
1425         .svhs           = 2,
1426         .gpiomask       = 15,
1427         .muxsel         = MUXSEL(2, 3, 1, 1),
1428         .gpiomux        = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */
1429         .gpiomute   = 13,
1430         .pll            = PLL_28,
1431         .tuner_type     = TUNER_LG_PAL_I_FM,
1432         .tuner_addr = ADDR_UNSET,
1433         .has_remote     = 1,
1434         /* GPIO wiring:
1435             GPIO0: U4.A0 (hef4052bt)
1436             GPIO1: U4.A1
1437             GPIO2: U4.A1 (second hef4052bt)
1438             GPIO3: U4.nEN, U5.A0, A5.nEN
1439             GPIO8-15: vrd866b ?
1440         */
1441     },
1442     [BTTV_BOARD_FLYVIDEO98EZ] = {
1443         .name       = "Lifeview FlyVideo 98EZ (capture only) LR51",
1444         .video_inputs   = 4,
1445         /* .audio_inputs= 0, */
1446         .svhs       = 2,
1447         /* AV1, AV2, SVHS, CVid adapter on SVHS */
1448         .muxsel     = MUXSEL(2, 3, 1, 1),
1449         .pll        = PLL_28,
1450         .no_msp34xx = 1,
1451         .tuner_type = TUNER_ABSENT,
1452         .tuner_addr = ADDR_UNSET,
1453     },
1454 
1455     /* ---- card 0x48 ---------------------------------- */
1456     [BTTV_BOARD_PV_BT878P_9B] = {
1457         /* Dariusz Kowalewski <darekk@automex.pl> */
1458         .name       = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)",
1459         .video_inputs   = 4,
1460         /* .audio_inputs= 1, */
1461         .svhs       = 2,
1462         .gpiomask   = 0x3f,
1463         .muxsel     = MUXSEL(2, 3, 1, 1),
1464         .gpiomux    = { 0x01, 0x00, 0x03, 0x03 },
1465         .gpiomute   = 0x09,
1466         .no_msp34xx = 1,
1467         .pll        = PLL_28,
1468         .tuner_type = TUNER_PHILIPS_PAL,
1469         .tuner_addr = ADDR_UNSET,
1470         .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */
1471         .has_radio  = 1,  /* Note: not all cards have radio */
1472         .has_remote     = 1,
1473         /* GPIO wiring:
1474             GPIO0: A0 hef4052
1475             GPIO1: A1 hef4052
1476             GPIO3: nEN hef4052
1477             GPIO8-15: vrd866b
1478             GPIO20,22,23: R30,R29,R28
1479         */
1480     },
1481     [BTTV_BOARD_SENSORAY311_611] = {
1482         /* Clay Kunz <ckunz@mail.arc.nasa.gov> */
1483         /* you must jumper JP5 for the 311 card (PC/104+) to work */
1484         .name           = "Sensoray 311/611",
1485         .video_inputs   = 5,
1486         /* .audio_inputs= 0, */
1487         .svhs           = 4,
1488         .gpiomask       = 0,
1489         .muxsel         = MUXSEL(2, 3, 1, 0, 0),
1490         .gpiomux        = { 0 },
1491         .tuner_type     = TUNER_ABSENT,
1492         .tuner_addr = ADDR_UNSET,
1493     },
1494     [BTTV_BOARD_RV605] = {
1495         /* Miguel Freitas <miguel@cetuc.puc-rio.br> */
1496         .name           = "RemoteVision MX (RV605)",
1497         .video_inputs   = 16,
1498         /* .audio_inputs= 0, */
1499         .svhs           = NO_SVHS,
1500         .gpiomask       = 0x00,
1501         .gpiomask2      = 0x07ff,
1502         .muxsel         = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
1503         .no_msp34xx     = 1,
1504         .tuner_type     = TUNER_ABSENT,
1505         .tuner_addr = ADDR_UNSET,
1506         .muxsel_hook    = rv605_muxsel,
1507     },
1508     [BTTV_BOARD_POWERCLR_MTV878] = {
1509         .name           = "Powercolor MTV878/ MTV878R/ MTV878F",
1510         .video_inputs   = 3,
1511         /* .audio_inputs= 2, */
1512         .svhs           = 2,
1513         .gpiomask       = 0x1C800F,  /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */
1514         .muxsel         = MUXSEL(2, 1, 1),
1515         .gpiomux        = { 0, 1, 2, 2 },
1516         .gpiomute   = 4,
1517         .tuner_type     = TUNER_PHILIPS_PAL,
1518         .tuner_addr = ADDR_UNSET,
1519         .pll        = PLL_28,
1520         .has_radio  = 1,
1521     },
1522 
1523     /* ---- card 0x4c ---------------------------------- */
1524     [BTTV_BOARD_WINDVR] = {
1525         /* Masaki Suzuki <masaki@btree.org> */
1526         .name           = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)",
1527         .video_inputs   = 3,
1528         /* .audio_inputs= 1, */
1529         .svhs           = 2,
1530         .gpiomask       = 0x140007,
1531         .muxsel         = MUXSEL(2, 3, 1, 1),
1532         .gpiomux        = { 0, 1, 2, 3 },
1533         .gpiomute   = 4,
1534         .tuner_type     = TUNER_PHILIPS_NTSC,
1535         .tuner_addr = ADDR_UNSET,
1536         .audio_mode_gpio= windvr_audio,
1537     },
1538     [BTTV_BOARD_GRANDTEC_MULTI] = {
1539         .name           = "GrandTec Multi Capture Card (Bt878)",
1540         .video_inputs   = 4,
1541         /* .audio_inputs= 0, */
1542         .svhs           = NO_SVHS,
1543         .gpiomask       = 0,
1544         .muxsel         = MUXSEL(2, 3, 1, 0),
1545         .gpiomux        = { 0 },
1546         .no_msp34xx     = 1,
1547         .pll            = PLL_28,
1548         .tuner_type     = TUNER_ABSENT,
1549         .tuner_addr = ADDR_UNSET,
1550     },
1551     [BTTV_BOARD_KWORLD] = {
1552         .name           = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF",
1553         .video_inputs   = 4,
1554         /* .audio_inputs= 3, */
1555         .svhs           = 2,
1556         .gpiomask       = 7,
1557         /* Tuner, SVid, SVHS, SVid to SVHS connector */
1558         .muxsel         = MUXSEL(2, 3, 1, 1),
1559         .gpiomux        = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio!
1560                         * This card lacks external Audio In, so we mute it on Ext. & Int.
1561                         * The PCB can take a sbx1637/sbx1673, wiring unknown.
1562                         * This card lacks PCI subsystem ID, sigh.
1563                         * gpiomux =1: lower volume, 2+3: mute
1564                         * btwincap uses 0x80000/0x80003
1565                         */
1566         .gpiomute   = 4,
1567         .no_msp34xx     = 1,
1568         .pll            = PLL_28,
1569         .tuner_type     = TUNER_PHILIPS_PAL,
1570         .tuner_addr = ADDR_UNSET,
1571         /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and
1572         radio signal strength indicators work fine. */
1573         .has_radio  = 1,
1574         /* GPIO Info:
1575             GPIO0,1:   HEF4052 A0,A1
1576             GPIO2:     HEF4052 nENABLE
1577             GPIO3-7:   n.c.
1578             GPIO8-13:  IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card]
1579             GPIO14,15: ??
1580             GPIO16-21: n.c.
1581             GPIO22,23: ??
1582             ??       : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/
1583     },
1584     [BTTV_BOARD_DSP_TCVIDEO] = {
1585         /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */
1586         .name           = "DSP Design TCVIDEO",
1587         .video_inputs   = 4,
1588         .svhs           = NO_SVHS,
1589         .muxsel         = MUXSEL(2, 3, 1, 0),
1590         .pll            = PLL_28,
1591         .tuner_type     = UNSET,
1592         .tuner_addr = ADDR_UNSET,
1593     },
1594 
1595         /* ---- card 0x50 ---------------------------------- */
1596     [BTTV_BOARD_HAUPPAUGEPVR] = {
1597         .name           = "Hauppauge WinTV PVR",
1598         .video_inputs   = 4,
1599         /* .audio_inputs= 1, */
1600         .svhs           = 2,
1601         .muxsel         = MUXSEL(2, 0, 1, 1),
1602         .pll            = PLL_28,
1603         .tuner_type     = UNSET,
1604         .tuner_addr = ADDR_UNSET,
1605 
1606         .gpiomask       = 7,
1607         .gpiomux        = {7},
1608     },
1609     [BTTV_BOARD_GVBCTV5PCI] = {
1610         .name           = "IODATA GV-BCTV5/PCI",
1611         .video_inputs   = 3,
1612         /* .audio_inputs= 1, */
1613         .svhs           = 2,
1614         .gpiomask       = 0x0f0f80,
1615         .muxsel         = MUXSEL(2, 3, 1, 0),
1616         .gpiomux        = {0x030000, 0x010000, 0, 0 },
1617         .gpiomute   = 0x020000,
1618         .no_msp34xx     = 1,
1619         .pll            = PLL_28,
1620         .tuner_type     = TUNER_PHILIPS_NTSC_M,
1621         .tuner_addr = ADDR_UNSET,
1622         .audio_mode_gpio= gvbctv5pci_audio,
1623         .has_radio      = 1,
1624     },
1625     [BTTV_BOARD_OSPREY1x0] = {
1626         .name           = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */
1627         .video_inputs   = 4,                  /* id-inputs-clock */
1628         /* .audio_inputs= 0, */
1629         .svhs           = 3,
1630         .muxsel         = MUXSEL(3, 2, 0, 1),
1631         .pll            = PLL_28,
1632         .tuner_type     = TUNER_ABSENT,
1633         .tuner_addr = ADDR_UNSET,
1634         .no_msp34xx     = 1,
1635         .no_tda7432     = 1,
1636     },
1637     [BTTV_BOARD_OSPREY1x0_848] = {
1638         .name           = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */
1639         .video_inputs   = 3,
1640         /* .audio_inputs= 0, */
1641         .svhs           = 2,
1642         .muxsel         = MUXSEL(2, 3, 1),
1643         .pll            = PLL_28,
1644         .tuner_type     = TUNER_ABSENT,
1645         .tuner_addr = ADDR_UNSET,
1646         .no_msp34xx     = 1,
1647         .no_tda7432     = 1,
1648     },
1649 
1650         /* ---- card 0x54 ---------------------------------- */
1651     [BTTV_BOARD_OSPREY101_848] = {
1652         .name           = "Osprey 101 (848)", /* 0x05-40C0-C1 */
1653         .video_inputs   = 2,
1654         /* .audio_inputs= 0, */
1655         .svhs           = 1,
1656         .muxsel         = MUXSEL(3, 1),
1657         .pll            = PLL_28,
1658         .tuner_type     = TUNER_ABSENT,
1659         .tuner_addr = ADDR_UNSET,
1660         .no_msp34xx     = 1,
1661         .no_tda7432     = 1,
1662     },
1663     [BTTV_BOARD_OSPREY1x1] = {
1664         .name           = "Osprey 101/151",       /* 0x1(4|5)-0004-C4 */
1665         .video_inputs   = 1,
1666         /* .audio_inputs= 0, */
1667         .svhs           = NO_SVHS,
1668         .muxsel         = MUXSEL(0),
1669         .pll            = PLL_28,
1670         .tuner_type     = TUNER_ABSENT,
1671         .tuner_addr = ADDR_UNSET,
1672         .no_msp34xx     = 1,
1673         .no_tda7432     = 1,
1674     },
1675     [BTTV_BOARD_OSPREY1x1_SVID] = {
1676         .name           = "Osprey 101/151 w/ svid",  /* 0x(16|17|20)-00C4-C1 */
1677         .video_inputs   = 2,
1678         /* .audio_inputs= 0, */
1679         .svhs           = 1,
1680         .muxsel         = MUXSEL(0, 1),
1681         .pll            = PLL_28,
1682         .tuner_type     = TUNER_ABSENT,
1683         .tuner_addr = ADDR_UNSET,
1684         .no_msp34xx     = 1,
1685         .no_tda7432     = 1,
1686     },
1687     [BTTV_BOARD_OSPREY2xx] = {
1688         .name           = "Osprey 200/201/250/251",  /* 0x1(8|9|E|F)-0004-C4 */
1689         .video_inputs   = 1,
1690         /* .audio_inputs= 1, */
1691         .svhs           = NO_SVHS,
1692         .muxsel         = MUXSEL(0),
1693         .pll            = PLL_28,
1694         .tuner_type = TUNER_ABSENT,
1695         .tuner_addr = ADDR_UNSET,
1696         .no_msp34xx     = 1,
1697         .no_tda7432     = 1,
1698     },
1699 
1700         /* ---- card 0x58 ---------------------------------- */
1701     [BTTV_BOARD_OSPREY2x0_SVID] = {
1702         .name           = "Osprey 200/250",   /* 0x1(A|B)-00C4-C1 */
1703         .video_inputs   = 2,
1704         /* .audio_inputs= 1, */
1705         .svhs           = 1,
1706         .muxsel         = MUXSEL(0, 1),
1707         .pll            = PLL_28,
1708         .tuner_type = TUNER_ABSENT,
1709         .tuner_addr = ADDR_UNSET,
1710         .no_msp34xx     = 1,
1711         .no_tda7432     = 1,
1712     },
1713     [BTTV_BOARD_OSPREY2x0] = {
1714         .name           = "Osprey 210/220/230",   /* 0x1(A|B)-04C0-C1 */
1715         .video_inputs   = 2,
1716         /* .audio_inputs= 1, */
1717         .svhs           = 1,
1718         .muxsel         = MUXSEL(2, 3),
1719         .pll            = PLL_28,
1720         .tuner_type = TUNER_ABSENT,
1721         .tuner_addr = ADDR_UNSET,
1722         .no_msp34xx     = 1,
1723         .no_tda7432     = 1,
1724     },
1725     [BTTV_BOARD_OSPREY500] = {
1726         .name           = "Osprey 500",   /* 500 */
1727         .video_inputs   = 2,
1728         /* .audio_inputs= 1, */
1729         .svhs           = 1,
1730         .muxsel         = MUXSEL(2, 3),
1731         .pll            = PLL_28,
1732         .tuner_type     = TUNER_ABSENT,
1733         .tuner_addr = ADDR_UNSET,
1734         .no_msp34xx     = 1,
1735         .no_tda7432     = 1,
1736     },
1737     [BTTV_BOARD_OSPREY540] = {
1738         .name           = "Osprey 540",   /* 540 */
1739         .video_inputs   = 4,
1740         /* .audio_inputs= 1, */
1741         .pll            = PLL_28,
1742         .tuner_type     = TUNER_ABSENT,
1743         .tuner_addr = ADDR_UNSET,
1744         .no_msp34xx     = 1,
1745         .no_tda7432     = 1,
1746     },
1747 
1748         /* ---- card 0x5C ---------------------------------- */
1749     [BTTV_BOARD_OSPREY2000] = {
1750         .name           = "Osprey 2000",  /* 2000 */
1751         .video_inputs   = 2,
1752         /* .audio_inputs= 1, */
1753         .svhs           = 1,
1754         .muxsel         = MUXSEL(2, 3),
1755         .pll            = PLL_28,
1756         .tuner_type = TUNER_ABSENT,
1757         .tuner_addr = ADDR_UNSET,
1758         .no_msp34xx     = 1,
1759         .no_tda7432     = 1,      /* must avoid, conflicts with the bt860 */
1760     },
1761     [BTTV_BOARD_IDS_EAGLE] = {
1762         /* M G Berberich <berberic@forwiss.uni-passau.de> */
1763         .name           = "IDS Eagle",
1764         .video_inputs   = 4,
1765         /* .audio_inputs= 0, */
1766         .tuner_type     = TUNER_ABSENT,
1767         .tuner_addr = ADDR_UNSET,
1768         .svhs           = NO_SVHS,
1769         .gpiomask       = 0,
1770         .muxsel         = MUXSEL(2, 2, 2, 2),
1771         .muxsel_hook    = eagle_muxsel,
1772         .no_msp34xx     = 1,
1773         .pll            = PLL_28,
1774     },
1775     [BTTV_BOARD_PINNACLESAT] = {
1776         .name           = "Pinnacle PCTV Sat",
1777         .video_inputs   = 2,
1778         /* .audio_inputs= 0, */
1779         .svhs           = 1,
1780         .tuner_type     = TUNER_ABSENT,
1781         .tuner_addr = ADDR_UNSET,
1782         .no_msp34xx     = 1,
1783         .no_tda7432     = 1,
1784         .muxsel         = MUXSEL(3, 1),
1785         .pll            = PLL_28,
1786         .no_gpioirq     = 1,
1787         .has_dvb        = 1,
1788     },
1789     [BTTV_BOARD_FORMAC_PROTV] = {
1790         .name           = "Formac ProTV II (bt878)",
1791         .video_inputs   = 4,
1792         /* .audio_inputs= 1, */
1793         .svhs           = 3,
1794         .gpiomask       = 2,
1795         /* TV, Comp1, Composite over SVID con, SVID */
1796         .muxsel         = MUXSEL(2, 3, 1, 1),
1797         .gpiomux        = { 2, 2, 0, 0 },
1798         .pll            = PLL_28,
1799         .has_radio      = 1,
1800         .tuner_type     = TUNER_PHILIPS_PAL,
1801         .tuner_addr = ADDR_UNSET,
1802     /* sound routing:
1803         GPIO=0x00,0x01,0x03: mute (?)
1804         0x02: both TV and radio (tuner: FM1216/I)
1805         The card has onboard audio connectors labeled "cdrom" and "board",
1806         not soldered here, though unknown wiring.
1807         Card lacks: external audio in, pci subsystem id.
1808     */
1809     },
1810 
1811         /* ---- card 0x60 ---------------------------------- */
1812     [BTTV_BOARD_MACHTV] = {
1813         .name           = "MachTV",
1814         .video_inputs   = 3,
1815         /* .audio_inputs= 1, */
1816         .svhs           = NO_SVHS,
1817         .gpiomask       = 7,
1818         .muxsel         = MUXSEL(2, 3, 1, 1),
1819         .gpiomux        = { 0, 1, 2, 3},
1820         .gpiomute   = 4,
1821         .tuner_type     = TUNER_PHILIPS_PAL,
1822         .tuner_addr = ADDR_UNSET,
1823         .pll            = PLL_28,
1824     },
1825     [BTTV_BOARD_EURESYS_PICOLO] = {
1826         .name           = "Euresys Picolo",
1827         .video_inputs   = 3,
1828         /* .audio_inputs= 0, */
1829         .svhs           = 2,
1830         .gpiomask       = 0,
1831         .no_msp34xx     = 1,
1832         .no_tda7432     = 1,
1833         .muxsel         = MUXSEL(2, 0, 1),
1834         .pll            = PLL_28,
1835         .tuner_type     = TUNER_ABSENT,
1836         .tuner_addr = ADDR_UNSET,
1837     },
1838     [BTTV_BOARD_PV150] = {
1839         /* Luc Van Hoeylandt <luc@e-magic.be> */
1840         .name           = "ProVideo PV150", /* 0x4f */
1841         .video_inputs   = 2,
1842         /* .audio_inputs= 0, */
1843         .svhs           = NO_SVHS,
1844         .gpiomask       = 0,
1845         .muxsel         = MUXSEL(2, 3),
1846         .gpiomux        = { 0 },
1847         .no_msp34xx     = 1,
1848         .pll            = PLL_28,
1849         .tuner_type     = TUNER_ABSENT,
1850         .tuner_addr = ADDR_UNSET,
1851     },
1852     [BTTV_BOARD_AD_TVK503] = {
1853         /* Hiroshi Takekawa <sian@big.or.jp> */
1854         /* This card lacks subsystem ID */
1855         .name           = "AD-TVK503", /* 0x63 */
1856         .video_inputs   = 4,
1857         /* .audio_inputs= 1, */
1858         .svhs           = 2,
1859         .gpiomask       = 0x001e8007,
1860         .muxsel         = MUXSEL(2, 3, 1, 0),
1861         /*                  Tuner, Radio, external, internal, off,  on */
1862         .gpiomux        = { 0x08,  0x0f,  0x0a,     0x08 },
1863         .gpiomute   = 0x0f,
1864         .no_msp34xx     = 1,
1865         .pll            = PLL_28,
1866         .tuner_type     = TUNER_PHILIPS_NTSC,
1867         .tuner_addr = ADDR_UNSET,
1868         .audio_mode_gpio= adtvk503_audio,
1869     },
1870 
1871         /* ---- card 0x64 ---------------------------------- */
1872     [BTTV_BOARD_HERCULES_SM_TV] = {
1873         .name           = "Hercules Smart TV Stereo",
1874         .video_inputs   = 4,
1875         /* .audio_inputs= 1, */
1876         .svhs           = 2,
1877         .gpiomask       = 0x00,
1878         .muxsel         = MUXSEL(2, 3, 1, 1),
1879         .no_msp34xx     = 1,
1880         .pll            = PLL_28,
1881         .tuner_type     = TUNER_PHILIPS_PAL,
1882         .tuner_addr = ADDR_UNSET,
1883         /* Notes:
1884         - card lacks subsystem ID
1885         - stereo variant w/ daughter board with tda9874a @0xb0
1886         - Audio Routing:
1887             always from tda9874 independent of GPIO (?)
1888             external line in: unknown
1889         - Other chips: em78p156elp @ 0x96 (probably IR remote control)
1890             hef4053 (instead 4052) for unknown function
1891         */
1892     },
1893     [BTTV_BOARD_PACETV] = {
1894         .name           = "Pace TV & Radio Card",
1895         .video_inputs   = 4,
1896         /* .audio_inputs= 1, */
1897         .svhs           = 2,
1898         /* Tuner, CVid, SVid, CVid over SVid connector */
1899         .muxsel         = MUXSEL(2, 3, 1, 1),
1900         .gpiomask       = 0,
1901         .no_tda7432     = 1,
1902         .tuner_type     = TUNER_PHILIPS_PAL_I,
1903         .tuner_addr = ADDR_UNSET,
1904         .has_radio      = 1,
1905         .pll            = PLL_28,
1906         /* Bt878, Bt832, FI1246 tuner; no pci subsystem id
1907         only internal line out: (4pin header) RGGL
1908         Radio must be decoded by msp3410d (not routed through)*/
1909         /*
1910         .digital_mode   = DIGITAL_MODE_CAMERA,  todo!
1911         */
1912     },
1913     [BTTV_BOARD_IVC200] = {
1914         /* Chris Willing <chris@vislab.usyd.edu.au> */
1915         .name           = "IVC-200",
1916         .video_inputs   = 1,
1917         /* .audio_inputs= 0, */
1918         .tuner_type     = TUNER_ABSENT,
1919         .tuner_addr = ADDR_UNSET,
1920         .svhs           = NO_SVHS,
1921         .gpiomask       = 0xdf,
1922         .muxsel         = MUXSEL(2),
1923         .pll            = PLL_28,
1924     },
1925     [BTTV_BOARD_IVCE8784] = {
1926         .name           = "IVCE-8784",
1927         .video_inputs   = 1,
1928         /* .audio_inputs= 0, */
1929         .tuner_type     = TUNER_ABSENT,
1930         .tuner_addr     = ADDR_UNSET,
1931         .svhs           = NO_SVHS,
1932         .gpiomask       = 0xdf,
1933         .muxsel         = MUXSEL(2),
1934         .pll            = PLL_28,
1935     },
1936     [BTTV_BOARD_XGUARD] = {
1937         .name           = "Grand X-Guard / Trust 814PCI",
1938         .video_inputs   = 16,
1939         /* .audio_inputs= 0, */
1940         .svhs           = NO_SVHS,
1941         .tuner_type     = TUNER_ABSENT,
1942         .tuner_addr = ADDR_UNSET,
1943         .gpiomask2      = 0xff,
1944         .muxsel         = MUXSEL(2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0),
1945         .muxsel_hook    = xguard_muxsel,
1946         .no_msp34xx     = 1,
1947         .no_tda7432     = 1,
1948         .pll            = PLL_28,
1949     },
1950 
1951         /* ---- card 0x68 ---------------------------------- */
1952     [BTTV_BOARD_NEBULA_DIGITV] = {
1953         .name           = "Nebula Electronics DigiTV",
1954         .video_inputs   = 1,
1955         .svhs           = NO_SVHS,
1956         .muxsel         = MUXSEL(2, 3, 1, 0),
1957         .no_msp34xx     = 1,
1958         .no_tda7432     = 1,
1959         .pll            = PLL_28,
1960         .tuner_type     = TUNER_ABSENT,
1961         .tuner_addr = ADDR_UNSET,
1962         .has_dvb        = 1,
1963         .has_remote = 1,
1964         .gpiomask   = 0x1b,
1965         .no_gpioirq     = 1,
1966     },
1967     [BTTV_BOARD_PV143] = {
1968         /* Jorge Boncompte - DTI2 <jorge@dti2.net> */
1969         .name           = "ProVideo PV143",
1970         .video_inputs   = 4,
1971         /* .audio_inputs= 0, */
1972         .svhs           = NO_SVHS,
1973         .gpiomask       = 0,
1974         .muxsel         = MUXSEL(2, 3, 1, 0),
1975         .gpiomux        = { 0 },
1976         .no_msp34xx     = 1,
1977         .pll            = PLL_28,
1978         .tuner_type     = TUNER_ABSENT,
1979         .tuner_addr = ADDR_UNSET,
1980     },
1981     [BTTV_BOARD_VD009X1_VD011_MINIDIN] = {
1982         /* M.Klahr@phytec.de */
1983         .name           = "PHYTEC VD-009-X1 VD-011 MiniDIN (bt878)",
1984         .video_inputs   = 4,
1985         /* .audio_inputs= 0, */
1986         .svhs           = 3,
1987         .gpiomask       = 0x00,
1988         .muxsel         = MUXSEL(2, 3, 1, 0),
1989         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
1990         .pll            = PLL_28,
1991         .tuner_type     = TUNER_ABSENT,
1992         .tuner_addr = ADDR_UNSET,
1993     },
1994     [BTTV_BOARD_VD009X1_VD011_COMBI] = {
1995         .name           = "PHYTEC VD-009-X1 VD-011 Combi (bt878)",
1996         .video_inputs   = 4,
1997         /* .audio_inputs= 0, */
1998         .svhs           = 3,
1999         .gpiomask       = 0x00,
2000         .muxsel         = MUXSEL(2, 3, 1, 1),
2001         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2002         .pll            = PLL_28,
2003         .tuner_type     = TUNER_ABSENT,
2004         .tuner_addr = ADDR_UNSET,
2005     },
2006 
2007         /* ---- card 0x6c ---------------------------------- */
2008     [BTTV_BOARD_VD009_MINIDIN] = {
2009         .name           = "PHYTEC VD-009 MiniDIN (bt878)",
2010         .video_inputs   = 10,
2011         /* .audio_inputs= 0, */
2012         .svhs           = 9,
2013         .gpiomask       = 0x00,
2014         .gpiomask2      = 0x03, /* used for external video mux */
2015         .muxsel         = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 0),
2016         .muxsel_hook    = phytec_muxsel,
2017         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2018         .pll            = PLL_28,
2019         .tuner_type     = TUNER_ABSENT,
2020         .tuner_addr = ADDR_UNSET,
2021     },
2022     [BTTV_BOARD_VD009_COMBI] = {
2023         .name           = "PHYTEC VD-009 Combi (bt878)",
2024         .video_inputs   = 10,
2025         /* .audio_inputs= 0, */
2026         .svhs           = 9,
2027         .gpiomask       = 0x00,
2028         .gpiomask2      = 0x03, /* used for external video mux */
2029         .muxsel         = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),
2030         .muxsel_hook    = phytec_muxsel,
2031         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2032         .pll            = PLL_28,
2033         .tuner_type     = TUNER_ABSENT,
2034         .tuner_addr = ADDR_UNSET,
2035     },
2036     [BTTV_BOARD_IVC100] = {
2037         .name           = "IVC-100",
2038         .video_inputs   = 4,
2039         /* .audio_inputs= 0, */
2040         .tuner_type     = TUNER_ABSENT,
2041         .tuner_addr = ADDR_UNSET,
2042         .svhs           = NO_SVHS,
2043         .gpiomask       = 0xdf,
2044         .muxsel         = MUXSEL(2, 3, 1, 0),
2045         .pll            = PLL_28,
2046     },
2047     [BTTV_BOARD_IVC120] = {
2048         /* IVC-120G - Alan Garfield <alan@fromorbit.com> */
2049         .name           = "IVC-120G",
2050         .video_inputs   = 16,
2051         /* .audio_inputs= 0, */
2052         .tuner_type     = TUNER_ABSENT,
2053         .tuner_addr = ADDR_UNSET,
2054         .svhs           = NO_SVHS,   /* card has no svhs */
2055         .no_msp34xx     = 1,
2056         .no_tda7432     = 1,
2057         .gpiomask       = 0x00,
2058         .muxsel         = MUXSEL(0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0),
2059         .muxsel_hook    = ivc120_muxsel,
2060         .pll            = PLL_28,
2061     },
2062 
2063         /* ---- card 0x70 ---------------------------------- */
2064     [BTTV_BOARD_PC_HDTV] = {
2065         .name           = "pcHDTV HD-2000 TV",
2066         .video_inputs   = 4,
2067         /* .audio_inputs= 1, */
2068         .svhs           = 2,
2069         .muxsel         = MUXSEL(2, 3, 1, 0),
2070         .tuner_type     = TUNER_PHILIPS_FCV1236D,
2071         .tuner_addr = ADDR_UNSET,
2072         .has_dvb        = 1,
2073     },
2074     [BTTV_BOARD_TWINHAN_DST] = {
2075         .name           = "Twinhan DST + clones",
2076         .no_msp34xx     = 1,
2077         .no_tda7432     = 1,
2078         .tuner_type     = TUNER_ABSENT,
2079         .tuner_addr = ADDR_UNSET,
2080         .no_video       = 1,
2081         .has_dvb        = 1,
2082     },
2083     [BTTV_BOARD_WINFASTVC100] = {
2084         .name           = "Winfast VC100",
2085         .video_inputs   = 3,
2086         /* .audio_inputs= 0, */
2087         .svhs           = 1,
2088         /* Vid In, SVid In, Vid over SVid in connector */
2089         .muxsel     = MUXSEL(3, 1, 1, 3),
2090         .no_msp34xx     = 1,
2091         .no_tda7432     = 1,
2092         .tuner_type     = TUNER_ABSENT,
2093         .tuner_addr = ADDR_UNSET,
2094         .pll            = PLL_28,
2095     },
2096     [BTTV_BOARD_TEV560] = {
2097         .name           = "Teppro TEV-560/InterVision IV-560",
2098         .video_inputs   = 3,
2099         /* .audio_inputs= 1, */
2100         .svhs           = 2,
2101         .gpiomask       = 3,
2102         .muxsel         = MUXSEL(2, 3, 1, 1),
2103         .gpiomux        = { 1, 1, 1, 1 },
2104         .tuner_type     = TUNER_PHILIPS_PAL,
2105         .tuner_addr = ADDR_UNSET,
2106         .pll            = PLL_35,
2107     },
2108 
2109         /* ---- card 0x74 ---------------------------------- */
2110     [BTTV_BOARD_SIMUS_GVC1100] = {
2111         .name           = "SIMUS GVC1100",
2112         .video_inputs   = 4,
2113         /* .audio_inputs= 0, */
2114         .svhs           = NO_SVHS,
2115         .tuner_type     = TUNER_ABSENT,
2116         .tuner_addr = ADDR_UNSET,
2117         .pll            = PLL_28,
2118         .muxsel         = MUXSEL(2, 2, 2, 2),
2119         .gpiomask       = 0x3F,
2120         .muxsel_hook    = gvc1100_muxsel,
2121     },
2122     [BTTV_BOARD_NGSTV_PLUS] = {
2123         /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */
2124         .name           = "NGS NGSTV+",
2125         .video_inputs   = 3,
2126         .svhs           = 2,
2127         .gpiomask       = 0x008007,
2128         .muxsel         = MUXSEL(2, 3, 0, 0),
2129         .gpiomux        = { 0, 0, 0, 0 },
2130         .gpiomute   = 0x000003,
2131         .pll            = PLL_28,
2132         .tuner_type     = TUNER_PHILIPS_PAL,
2133         .tuner_addr = ADDR_UNSET,
2134         .has_remote     = 1,
2135     },
2136     [BTTV_BOARD_LMLBT4] = {
2137         /* http://linuxmedialabs.com */
2138         .name           = "LMLBT4",
2139         .video_inputs   = 4, /* IN1,IN2,IN3,IN4 */
2140         /* .audio_inputs= 0, */
2141         .svhs           = NO_SVHS,
2142         .muxsel         = MUXSEL(2, 3, 1, 0),
2143         .no_msp34xx     = 1,
2144         .no_tda7432     = 1,
2145         .tuner_type     = TUNER_ABSENT,
2146         .tuner_addr = ADDR_UNSET,
2147     },
2148     [BTTV_BOARD_TEKRAM_M205] = {
2149         /* Helmroos Harri <harri.helmroos@pp.inet.fi> */
2150         .name           = "Tekram M205 PRO",
2151         .video_inputs   = 3,
2152         /* .audio_inputs= 1, */
2153         .tuner_type     = TUNER_PHILIPS_PAL,
2154         .tuner_addr = ADDR_UNSET,
2155         .svhs           = 2,
2156         .gpiomask       = 0x68,
2157         .muxsel         = MUXSEL(2, 3, 1),
2158         .gpiomux        = { 0x68, 0x68, 0x61, 0x61 },
2159         .pll            = PLL_28,
2160     },
2161 
2162         /* ---- card 0x78 ---------------------------------- */
2163     [BTTV_BOARD_CONTVFMI] = {
2164         /* Javier Cendan Ares <jcendan@lycos.es> */
2165         /* bt878 TV + FM without subsystem ID */
2166         .name           = "Conceptronic CONTVFMi",
2167         .video_inputs   = 3,
2168         /* .audio_inputs= 1, */
2169         .svhs           = 2,
2170         .gpiomask       = 0x008007,
2171         .muxsel         = MUXSEL(2, 3, 1, 1),
2172         .gpiomux        = { 0, 1, 2, 2 },
2173         .gpiomute   = 3,
2174         .pll            = PLL_28,
2175         .tuner_type     = TUNER_PHILIPS_PAL,
2176         .tuner_addr = ADDR_UNSET,
2177         .has_remote     = 1,
2178         .has_radio      = 1,
2179     },
2180     [BTTV_BOARD_PICOLO_TETRA_CHIP] = {
2181         /*Eric DEBIEF <debief@telemsa.com>*/
2182         /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controlled*/
2183         /*adds picolo_tetra_muxsel(), picolo_tetra_init(), the following declaration*/
2184         /*structure and #define BTTV_BOARD_PICOLO_TETRA_CHIP 0x79 in bttv.h*/
2185         .name           = "Euresys Picolo Tetra",
2186         .video_inputs   = 4,
2187         /* .audio_inputs= 0, */
2188         .svhs           = NO_SVHS,
2189         .gpiomask       = 0,
2190         .gpiomask2      = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/
2191         .no_msp34xx     = 1,
2192         .no_tda7432     = 1,
2193         /*878A input is always MUX0, see above.*/
2194         .muxsel         = MUXSEL(2, 2, 2, 2),
2195         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2196         .pll            = PLL_28,
2197         .muxsel_hook    = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/
2198         .tuner_type     = TUNER_ABSENT,
2199         .tuner_addr = ADDR_UNSET,
2200     },
2201     [BTTV_BOARD_SPIRIT_TV] = {
2202         /* Spirit TV Tuner from http://spiritmodems.com.au */
2203         /* Stafford Goodsell <surge@goliath.homeunix.org> */
2204         .name           = "Spirit TV Tuner",
2205         .video_inputs   = 3,
2206         /* .audio_inputs= 1, */
2207         .svhs           = 2,
2208         .gpiomask       = 0x0000000f,
2209         .muxsel         = MUXSEL(2, 1, 1),
2210         .gpiomux        = { 0x02, 0x00, 0x00, 0x00 },
2211         .tuner_type     = TUNER_TEMIC_PAL,
2212         .tuner_addr = ADDR_UNSET,
2213         .no_msp34xx     = 1,
2214     },
2215     [BTTV_BOARD_AVDVBT_771] = {
2216         /* Wolfram Joost <wojo@frokaschwei.de> */
2217         .name           = "AVerMedia AVerTV DVB-T 771",
2218         .video_inputs   = 2,
2219         .svhs           = 1,
2220         .tuner_type     = TUNER_ABSENT,
2221         .tuner_addr = ADDR_UNSET,
2222         .muxsel         = MUXSEL(3, 3),
2223         .no_msp34xx     = 1,
2224         .no_tda7432     = 1,
2225         .pll            = PLL_28,
2226         .has_dvb        = 1,
2227         .no_gpioirq     = 1,
2228         .has_remote     = 1,
2229     },
2230         /* ---- card 0x7c ---------------------------------- */
2231     [BTTV_BOARD_AVDVBT_761] = {
2232         /* Matt Jesson <dvb@jesson.eclipse.co.uk> */
2233         /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */
2234         .name           = "AverMedia AverTV DVB-T 761",
2235         .video_inputs   = 2,
2236         .svhs           = 1,
2237         .muxsel         = MUXSEL(3, 1, 2, 0), /* Comp0, S-Video, ?, ? */
2238         .no_msp34xx     = 1,
2239         .no_tda7432     = 1,
2240         .pll            = PLL_28,
2241         .tuner_type     = TUNER_ABSENT,
2242         .tuner_addr = ADDR_UNSET,
2243         .has_dvb        = 1,
2244         .no_gpioirq     = 1,
2245         .has_remote     = 1,
2246     },
2247     [BTTV_BOARD_MATRIX_VISIONSQ] = {
2248         /* andre.schwarz@matrix-vision.de */
2249         .name       = "MATRIX Vision Sigma-SQ",
2250         .video_inputs   = 16,
2251         /* .audio_inputs= 0, */
2252         .svhs       = NO_SVHS,
2253         .gpiomask   = 0x0,
2254         .muxsel     = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3),
2255         .muxsel_hook    = sigmaSQ_muxsel,
2256         .gpiomux    = { 0 },
2257         .no_msp34xx = 1,
2258         .pll        = PLL_28,
2259         .tuner_type = TUNER_ABSENT,
2260         .tuner_addr = ADDR_UNSET,
2261     },
2262     [BTTV_BOARD_MATRIX_VISIONSLC] = {
2263         /* andre.schwarz@matrix-vision.de */
2264         .name       = "MATRIX Vision Sigma-SLC",
2265         .video_inputs   = 4,
2266         /* .audio_inputs= 0, */
2267         .svhs       = NO_SVHS,
2268         .gpiomask   = 0x0,
2269         .muxsel     = MUXSEL(2, 2, 2, 2),
2270         .muxsel_hook    = sigmaSLC_muxsel,
2271         .gpiomux    = { 0 },
2272         .no_msp34xx = 1,
2273         .pll        = PLL_28,
2274         .tuner_type = TUNER_ABSENT,
2275         .tuner_addr = ADDR_UNSET,
2276     },
2277         /* BTTV_BOARD_APAC_VIEWCOMP */
2278     [BTTV_BOARD_APAC_VIEWCOMP] = {
2279         /* Attila Kondoros <attila.kondoros@chello.hu> */
2280         /* bt878 TV + FM 0x00000000 subsystem ID */
2281         .name           = "APAC Viewcomp 878(AMAX)",
2282         .video_inputs   = 2,
2283         /* .audio_inputs= 1, */
2284         .svhs           = NO_SVHS,
2285         .gpiomask       = 0xFF,
2286         .muxsel         = MUXSEL(2, 3, 1, 1),
2287         .gpiomux        = { 2, 0, 0, 0 },
2288         .gpiomute   = 10,
2289         .pll            = PLL_28,
2290         .tuner_type     = TUNER_PHILIPS_PAL,
2291         .tuner_addr = ADDR_UNSET,
2292         .has_remote     = 1,   /* miniremote works, see ir-kbd-gpio.c */
2293         .has_radio      = 1,   /* not every card has radio */
2294     },
2295 
2296         /* ---- card 0x80 ---------------------------------- */
2297     [BTTV_BOARD_DVICO_DVBT_LITE] = {
2298         /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */
2299         .name           = "DViCO FusionHDTV DVB-T Lite",
2300         .no_msp34xx     = 1,
2301         .no_tda7432     = 1,
2302         .pll            = PLL_28,
2303         .no_video       = 1,
2304         .has_dvb        = 1,
2305         .tuner_type     = TUNER_ABSENT,
2306         .tuner_addr = ADDR_UNSET,
2307     },
2308     [BTTV_BOARD_VGEAR_MYVCD] = {
2309         /* Steven <photon38@pchome.com.tw> */
2310         .name           = "V-Gear MyVCD",
2311         .video_inputs   = 3,
2312         /* .audio_inputs= 1, */
2313         .svhs           = 2,
2314         .gpiomask       = 0x3f,
2315         .muxsel         = MUXSEL(2, 3, 1, 0),
2316         .gpiomux        = {0x31, 0x31, 0x31, 0x31 },
2317         .gpiomute   = 0x31,
2318         .no_msp34xx     = 1,
2319         .pll            = PLL_28,
2320         .tuner_type     = TUNER_PHILIPS_NTSC_M,
2321         .tuner_addr = ADDR_UNSET,
2322         .has_radio      = 0,
2323     },
2324     [BTTV_BOARD_SUPER_TV] = {
2325         /* Rick C <cryptdragoon@gmail.com> */
2326         .name           = "Super TV Tuner",
2327         .video_inputs   = 4,
2328         /* .audio_inputs= 1, */
2329         .svhs           = 2,
2330         .muxsel         = MUXSEL(2, 3, 1, 0),
2331         .tuner_type     = TUNER_PHILIPS_NTSC,
2332         .tuner_addr = ADDR_UNSET,
2333         .gpiomask       = 0x008007,
2334         .gpiomux        = { 0, 0x000001,0,0 },
2335         .has_radio      = 1,
2336     },
2337     [BTTV_BOARD_TIBET_CS16] = {
2338         /* Chris Fanning <video4linux@haydon.net> */
2339         .name           = "Tibet Systems 'Progress DVR' CS16",
2340         .video_inputs   = 16,
2341         /* .audio_inputs= 0, */
2342         .svhs           = NO_SVHS,
2343         .muxsel         = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2344         .pll        = PLL_28,
2345         .no_msp34xx     = 1,
2346         .no_tda7432 = 1,
2347         .tuner_type     = TUNER_ABSENT,
2348         .tuner_addr = ADDR_UNSET,
2349         .muxsel_hook    = tibetCS16_muxsel,
2350     },
2351     [BTTV_BOARD_KODICOM_4400R] = {
2352         /* Bill Brack <wbrack@mmm.com.hk> */
2353         /*
2354         * Note that, because of the card's wiring, the "master"
2355         * BT878A chip (i.e. the one which controls the analog switch
2356         * and must use this card type) is the 2nd one detected.  The
2357         * other 3 chips should use card type 0x85, whose description
2358         * follows this one.  There is a EEPROM on the card (which is
2359         * connected to the I2C of one of those other chips), but is
2360         * not currently handled.  There is also a facility for a
2361         * "monitor", which is also not currently implemented.
2362         */
2363         .name           = "Kodicom 4400R (master)",
2364         .video_inputs   = 16,
2365         /* .audio_inputs= 0, */
2366         .tuner_type = TUNER_ABSENT,
2367         .tuner_addr = ADDR_UNSET,
2368         .svhs       = NO_SVHS,
2369         /* GPIO bits 0-9 used for analog switch:
2370         *   00 - 03:    camera selector
2371         *   04 - 06:    channel (controller) selector
2372         *   07: data (1->on, 0->off)
2373         *   08: strobe
2374         *   09: reset
2375         * bit 16 is input from sync separator for the channel
2376         */
2377         .gpiomask   = 0x0003ff,
2378         .no_gpioirq     = 1,
2379         .muxsel     = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
2380         .pll        = PLL_28,
2381         .no_msp34xx = 1,
2382         .no_tda7432 = 1,
2383         .muxsel_hook    = kodicom4400r_muxsel,
2384     },
2385     [BTTV_BOARD_KODICOM_4400R_SL] = {
2386         /* Bill Brack <wbrack@mmm.com.hk> */
2387         /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the
2388         * one which controls the analog switch, and must use the card type)
2389         * is the 2nd one detected.  The other 3 chips should use this card
2390         * type
2391         */
2392         .name       = "Kodicom 4400R (slave)",
2393         .video_inputs   = 16,
2394         /* .audio_inputs= 0, */
2395         .tuner_type = TUNER_ABSENT,
2396         .tuner_addr = ADDR_UNSET,
2397         .svhs       = NO_SVHS,
2398         .gpiomask   = 0x010000,
2399         .no_gpioirq     = 1,
2400         .muxsel     = MUXSEL(3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3),
2401         .pll        = PLL_28,
2402         .no_msp34xx = 1,
2403         .no_tda7432 = 1,
2404         .muxsel_hook    = kodicom4400r_muxsel,
2405     },
2406         /* ---- card 0x86---------------------------------- */
2407     [BTTV_BOARD_ADLINK_RTV24] = {
2408         /* Michael Henson <mhenson@clarityvi.com> */
2409         /* Adlink RTV24 with special unlock codes */
2410         .name           = "Adlink RTV24",
2411         .video_inputs   = 4,
2412         /* .audio_inputs= 1, */
2413         .svhs           = 2,
2414         .muxsel         = MUXSEL(2, 3, 1, 0),
2415         .tuner_type     = UNSET,
2416         .tuner_addr = ADDR_UNSET,
2417         .pll            = PLL_28,
2418     },
2419         /* ---- card 0x87---------------------------------- */
2420     [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = {
2421         /* Michael Krufky <mkrufky@linuxtv.org> */
2422         .name           = "DViCO FusionHDTV 5 Lite",
2423         .tuner_type     = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */
2424         .tuner_addr = ADDR_UNSET,
2425         .video_inputs   = 3,
2426         /* .audio_inputs= 1, */
2427         .svhs           = 2,
2428         .muxsel     = MUXSEL(2, 3, 1),
2429         .gpiomask       = 0x00e00007,
2430         .gpiomux        = { 0x00400005, 0, 0x00000001, 0 },
2431         .gpiomute   = 0x00c00007,
2432         .no_msp34xx     = 1,
2433         .no_tda7432     = 1,
2434         .has_dvb        = 1,
2435     },
2436         /* ---- card 0x88---------------------------------- */
2437     [BTTV_BOARD_ACORP_Y878F] = {
2438         /* Mauro Carvalho Chehab <mchehab@kernel.org> */
2439         .name       = "Acorp Y878F",
2440         .video_inputs   = 3,
2441         /* .audio_inputs= 1, */
2442         .svhs       = 2,
2443         .gpiomask   = 0x01fe00,
2444         .muxsel     = MUXSEL(2, 3, 1, 1),
2445         .gpiomux        = { 0x001e00, 0, 0x018000, 0x014000 },
2446         .gpiomute   = 0x002000,
2447         .pll        = PLL_28,
2448         .tuner_type = TUNER_YMEC_TVF66T5_B_DFF,
2449         .tuner_addr = 0xc1 >>1,
2450         .has_radio  = 1,
2451     },
2452         /* ---- card 0x89 ---------------------------------- */
2453     [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = {
2454         .name           = "Conceptronic CTVFMi v2",
2455         .video_inputs   = 3,
2456         /* .audio_inputs= 1, */
2457         .svhs           = 2,
2458         .gpiomask       = 0x001c0007,
2459         .muxsel         = MUXSEL(2, 3, 1, 1),
2460         .gpiomux        = { 0, 1, 2, 2 },
2461         .gpiomute   = 3,
2462         .pll            = PLL_28,
2463         .tuner_type     = TUNER_TENA_9533_DI,
2464         .tuner_addr = ADDR_UNSET,
2465         .has_remote     = 1,
2466         .has_radio      = 1,
2467     },
2468         /* ---- card 0x8a ---------------------------------- */
2469     [BTTV_BOARD_PV_BT878P_2E] = {
2470         .name       = "Prolink Pixelview PV-BT878P+ (Rev.2E)",
2471         .video_inputs   = 5,
2472         /* .audio_inputs= 1, */
2473         .svhs       = 3,
2474         .has_dig_in = 1,
2475         .gpiomask   = 0x01fe00,
2476         .muxsel     = MUXSEL(2, 3, 1, 1, 0), /* in 4 is digital */
2477         /* .digital_mode= DIGITAL_MODE_CAMERA, */
2478         .gpiomux    = { 0x00400, 0x10400, 0x04400, 0x80000 },
2479         .gpiomute   = 0x12400,
2480         .no_msp34xx = 1,
2481         .pll        = PLL_28,
2482         .tuner_type = TUNER_LG_PAL_FM,
2483         .tuner_addr = ADDR_UNSET,
2484         .has_remote = 1,
2485     },
2486         /* ---- card 0x8b ---------------------------------- */
2487     [BTTV_BOARD_PV_M4900] = {
2488         /* Sérgio Fortier <sergiofortier@yahoo.com.br> */
2489         .name           = "Prolink PixelView PlayTV MPEG2 PV-M4900",
2490         .video_inputs   = 3,
2491         /* .audio_inputs= 1, */
2492         .svhs           = 2,
2493         .gpiomask       = 0x3f,
2494         .muxsel         = MUXSEL(2, 3, 1, 1),
2495         .gpiomux        = { 0x21, 0x20, 0x24, 0x2c },
2496         .gpiomute   = 0x29,
2497         .no_msp34xx     = 1,
2498         .pll            = PLL_28,
2499         .tuner_type     = TUNER_YMEC_TVF_5533MF,
2500         .tuner_addr     = ADDR_UNSET,
2501         .has_radio      = 1,
2502         .has_remote     = 1,
2503     },
2504         /* ---- card 0x8c ---------------------------------- */
2505     /* Has four Bt878 chips behind a PCI bridge, each chip has:
2506          one external BNC composite input (mux 2)
2507          three internal composite inputs (unknown muxes)
2508          an 18-bit stereo A/D (CS5331A), which has:
2509            one external stereo unbalanced (RCA) audio connection
2510            one (or 3?) internal stereo balanced (XLR) audio connection
2511            input is selected via gpio to a 14052B mux
2512          (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300)
2513            gain is controlled via an X9221A chip on the I2C bus @0x28
2514            sample rate is controlled via gpio to an MK1413S
2515          (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3)
2516          There is neither a tuner nor an svideo input. */
2517     [BTTV_BOARD_OSPREY440]  = {
2518         .name           = "Osprey 440",
2519         .video_inputs   = 4,
2520         /* .audio_inputs= 2, */
2521         .svhs           = NO_SVHS,
2522         .muxsel         = MUXSEL(2, 3, 0, 1), /* 3,0,1 are guesses */
2523         .gpiomask   = 0x303,
2524         .gpiomute   = 0x000, /* int + 32kHz */
2525         .gpiomux    = { 0, 0, 0x000, 0x100},
2526         .pll            = PLL_28,
2527         .tuner_type     = TUNER_ABSENT,
2528         .tuner_addr     = ADDR_UNSET,
2529         .no_msp34xx     = 1,
2530         .no_tda7432     = 1,
2531     },
2532         /* ---- card 0x8d ---------------------------------- */
2533     [BTTV_BOARD_ASOUND_SKYEYE] = {
2534         .name       = "Asound Skyeye PCTV",
2535         .video_inputs   = 3,
2536         /* .audio_inputs= 1, */
2537         .svhs       = 2,
2538         .gpiomask   = 15,
2539         .muxsel     = MUXSEL(2, 3, 1, 1),
2540         .gpiomux    = { 2, 0, 0, 0 },
2541         .gpiomute   = 1,
2542         .pll        = PLL_28,
2543         .tuner_type = TUNER_PHILIPS_NTSC,
2544         .tuner_addr = ADDR_UNSET,
2545     },
2546         /* ---- card 0x8e ---------------------------------- */
2547     [BTTV_BOARD_SABRENT_TVFM] = {
2548         .name       = "Sabrent TV-FM (bttv version)",
2549         .video_inputs   = 3,
2550         /* .audio_inputs= 1, */
2551         .svhs       = 2,
2552         .gpiomask   = 0x108007,
2553         .muxsel     = MUXSEL(2, 3, 1, 1),
2554         .gpiomux    = { 100000, 100002, 100002, 100000 },
2555         .no_msp34xx = 1,
2556         .no_tda7432     = 1,
2557         .pll        = PLL_28,
2558         .tuner_type = TUNER_TNF_5335MF,
2559         .tuner_addr = ADDR_UNSET,
2560         .has_radio      = 1,
2561     },
2562     /* ---- card 0x8f ---------------------------------- */
2563     [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = {
2564         .name       = "Hauppauge ImpactVCB (bt878)",
2565         .video_inputs   = 4,
2566         /* .audio_inputs= 0, */
2567         .svhs       = NO_SVHS,
2568         .gpiomask   = 0x0f, /* old: 7 */
2569         .muxsel     = MUXSEL(0, 1, 3, 2), /* Composite 0-3 */
2570         .no_msp34xx = 1,
2571         .no_tda7432     = 1,
2572         .tuner_type = TUNER_ABSENT,
2573         .tuner_addr = ADDR_UNSET,
2574     },
2575     [BTTV_BOARD_MACHTV_MAGICTV] = {
2576         /* Julian Calaby <julian.calaby@gmail.com>
2577          * Slightly different from original MachTV definition (0x60)
2578 
2579          * FIXME: RegSpy says gpiomask should be "0x001c800f", but it
2580          * stuffs up remote chip. Bug is a pin on the jaecs is not set
2581          * properly (methinks) causing no keyup bits being set */
2582 
2583         .name           = "MagicTV", /* rebranded MachTV */
2584         .video_inputs   = 3,
2585         /* .audio_inputs= 1, */
2586         .svhs           = 2,
2587         .gpiomask       = 7,
2588         .muxsel         = MUXSEL(2, 3, 1, 1),
2589         .gpiomux        = { 0, 1, 2, 3 },
2590         .gpiomute   = 4,
2591         .tuner_type     = TUNER_TEMIC_4009FR5_PAL,
2592         .tuner_addr     = ADDR_UNSET,
2593         .pll            = PLL_28,
2594         .has_radio      = 1,
2595         .has_remote     = 1,
2596     },
2597     [BTTV_BOARD_SSAI_SECURITY] = {
2598         .name       = "SSAI Security Video Interface",
2599         .video_inputs   = 4,
2600         /* .audio_inputs= 0, */
2601         .svhs       = NO_SVHS,
2602         .muxsel     = MUXSEL(0, 1, 2, 3),
2603         .tuner_type = TUNER_ABSENT,
2604         .tuner_addr = ADDR_UNSET,
2605     },
2606     [BTTV_BOARD_SSAI_ULTRASOUND] = {
2607         .name       = "SSAI Ultrasound Video Interface",
2608         .video_inputs   = 2,
2609         /* .audio_inputs= 0, */
2610         .svhs       = 1,
2611         .muxsel     = MUXSEL(2, 0, 1, 3),
2612         .tuner_type = TUNER_ABSENT,
2613         .tuner_addr = ADDR_UNSET,
2614     },
2615     /* ---- card 0x94---------------------------------- */
2616     [BTTV_BOARD_DVICO_FUSIONHDTV_2] = {
2617         .name           = "DViCO FusionHDTV 2",
2618         .tuner_type     = TUNER_PHILIPS_FCV1236D,
2619         .tuner_addr = ADDR_UNSET,
2620         .video_inputs   = 3,
2621         /* .audio_inputs= 1, */
2622         .svhs           = 2,
2623         .muxsel     = MUXSEL(2, 3, 1),
2624         .gpiomask       = 0x00e00007,
2625         .gpiomux        = { 0x00400005, 0, 0x00000001, 0 },
2626         .gpiomute   = 0x00c00007,
2627         .no_msp34xx     = 1,
2628         .no_tda7432     = 1,
2629     },
2630     /* ---- card 0x95---------------------------------- */
2631     [BTTV_BOARD_TYPHOON_TVTUNERPCI] = {
2632         .name           = "Typhoon TV-Tuner PCI (50684)",
2633         .video_inputs   = 3,
2634         /* .audio_inputs= 1, */
2635         .svhs           = 2,
2636         .gpiomask       = 0x3014f,
2637         .muxsel         = MUXSEL(2, 3, 1, 1),
2638         .gpiomux        = { 0x20001,0x10001, 0, 0 },
2639         .gpiomute       = 10,
2640         .pll            = PLL_28,
2641         .tuner_type     = TUNER_PHILIPS_PAL_I,
2642         .tuner_addr     = ADDR_UNSET,
2643     },
2644     [BTTV_BOARD_GEOVISION_GV600] = {
2645         /* emhn@usb.ve */
2646         .name       = "Geovision GV-600",
2647         .video_inputs   = 16,
2648         /* .audio_inputs= 0, */
2649         .svhs       = NO_SVHS,
2650         .gpiomask   = 0x0,
2651         .muxsel     = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2652         .muxsel_hook    = geovision_muxsel,
2653         .gpiomux    = { 0 },
2654         .no_msp34xx = 1,
2655         .pll        = PLL_28,
2656         .tuner_type = TUNER_ABSENT,
2657         .tuner_addr = ADDR_UNSET,
2658     },
2659     [BTTV_BOARD_KOZUMI_KTV_01C] = {
2660         /* Mauro Lacy <mauro@lacy.com.ar>
2661          * Based on MagicTV and Conceptronic CONTVFMi */
2662 
2663         .name           = "Kozumi KTV-01C",
2664         .video_inputs   = 3,
2665         /* .audio_inputs= 1, */
2666         .svhs           = 2,
2667         .gpiomask       = 0x008007,
2668         .muxsel         = MUXSEL(2, 3, 1, 1),
2669         .gpiomux        = { 0, 1, 2, 2 }, /* CONTVFMi */
2670         .gpiomute   = 3, /* CONTVFMi */
2671         .tuner_type     = TUNER_PHILIPS_FM1216ME_MK3, /* TCL MK3 */
2672         .tuner_addr     = ADDR_UNSET,
2673         .pll            = PLL_28,
2674         .has_radio      = 1,
2675         .has_remote     = 1,
2676     },
2677     [BTTV_BOARD_ENLTV_FM_2] = {
2678         /* Encore TV Tuner Pro ENL TV-FM-2
2679            Mauro Carvalho Chehab <mchehab@kernel.org> */
2680         .name           = "Encore ENL TV-FM-2",
2681         .video_inputs   = 3,
2682         /* .audio_inputs= 1, */
2683         .svhs           = 2,
2684         /* bit 6          -> IR disabled
2685            bit 18/17 = 00 -> mute
2686                    01 -> enable external audio input
2687                    10 -> internal audio input (mono?)
2688                    11 -> internal audio input
2689          */
2690         .gpiomask       = 0x060040,
2691         .muxsel         = MUXSEL(2, 3, 3),
2692         .gpiomux        = { 0x60000, 0x60000, 0x20000, 0x20000 },
2693         .gpiomute   = 0,
2694         .tuner_type = TUNER_TCL_MF02GIP_5N,
2695         .tuner_addr     = ADDR_UNSET,
2696         .pll            = PLL_28,
2697         .has_radio      = 1,
2698         .has_remote     = 1,
2699     },
2700     [BTTV_BOARD_VD012] = {
2701         /* D.Heer@Phytec.de */
2702         .name           = "PHYTEC VD-012 (bt878)",
2703         .video_inputs   = 4,
2704         /* .audio_inputs= 0, */
2705         .svhs           = NO_SVHS,
2706         .gpiomask       = 0x00,
2707         .muxsel         = MUXSEL(0, 2, 3, 1),
2708         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2709         .pll            = PLL_28,
2710         .tuner_type     = TUNER_ABSENT,
2711         .tuner_addr = ADDR_UNSET,
2712     },
2713     [BTTV_BOARD_VD012_X1] = {
2714         /* D.Heer@Phytec.de */
2715         .name           = "PHYTEC VD-012-X1 (bt878)",
2716         .video_inputs   = 4,
2717         /* .audio_inputs= 0, */
2718         .svhs           = 3,
2719         .gpiomask       = 0x00,
2720         .muxsel         = MUXSEL(2, 3, 1),
2721         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2722         .pll            = PLL_28,
2723         .tuner_type     = TUNER_ABSENT,
2724         .tuner_addr = ADDR_UNSET,
2725     },
2726     [BTTV_BOARD_VD012_X2] = {
2727         /* D.Heer@Phytec.de */
2728         .name           = "PHYTEC VD-012-X2 (bt878)",
2729         .video_inputs   = 4,
2730         /* .audio_inputs= 0, */
2731         .svhs           = 3,
2732         .gpiomask       = 0x00,
2733         .muxsel         = MUXSEL(3, 2, 1),
2734         .gpiomux        = { 0, 0, 0, 0 }, /* card has no audio */
2735         .pll            = PLL_28,
2736         .tuner_type     = TUNER_ABSENT,
2737         .tuner_addr = ADDR_UNSET,
2738     },
2739     [BTTV_BOARD_GEOVISION_GV800S] = {
2740         /* Bruno Christo <bchristo@inf.ufsm.br>
2741          *
2742          * GeoVision GV-800(S) has 4 Conexant Fusion 878A:
2743          *  1 audio input  per BT878A = 4 audio inputs
2744          *  4 video inputs per BT878A = 16 video inputs
2745          * This is the first BT878A chip of the GV-800(S). It's the
2746          * "master" chip and it controls the video inputs through an
2747          * analog multiplexer (a CD22M3494) via some GPIO pins. The
2748          * slaves should use card type 0x9e (following this one).
2749          * There is a EEPROM on the card which is currently not handled.
2750          * The audio input is not working yet.
2751          */
2752         .name           = "Geovision GV-800(S) (master)",
2753         .video_inputs   = 4,
2754         /* .audio_inputs= 1, */
2755         .tuner_type = TUNER_ABSENT,
2756         .tuner_addr = ADDR_UNSET,
2757         .svhs           = NO_SVHS,
2758         .gpiomask   = 0xf107f,
2759         .no_gpioirq     = 1,
2760         .muxsel     = MUXSEL(2, 2, 2, 2),
2761         .pll        = PLL_28,
2762         .no_msp34xx = 1,
2763         .no_tda7432 = 1,
2764         .muxsel_hook    = gv800s_muxsel,
2765     },
2766     [BTTV_BOARD_GEOVISION_GV800S_SL] = {
2767         /* Bruno Christo <bchristo@inf.ufsm.br>
2768          *
2769          * GeoVision GV-800(S) has 4 Conexant Fusion 878A:
2770          *  1 audio input  per BT878A = 4 audio inputs
2771          *  4 video inputs per BT878A = 16 video inputs
2772          * The 3 other BT878A chips are "slave" chips of the GV-800(S)
2773          * and should use this card type.
2774          * The audio input is not working yet.
2775          */
2776         .name           = "Geovision GV-800(S) (slave)",
2777         .video_inputs   = 4,
2778         /* .audio_inputs= 1, */
2779         .tuner_type = TUNER_ABSENT,
2780         .tuner_addr = ADDR_UNSET,
2781         .svhs           = NO_SVHS,
2782         .gpiomask   = 0x00,
2783         .no_gpioirq     = 1,
2784         .muxsel     = MUXSEL(2, 2, 2, 2),
2785         .pll        = PLL_28,
2786         .no_msp34xx = 1,
2787         .no_tda7432 = 1,
2788         .muxsel_hook    = gv800s_muxsel,
2789     },
2790     [BTTV_BOARD_PV183] = {
2791         .name           = "ProVideo PV183", /* 0x9f */
2792         .video_inputs   = 2,
2793         /* .audio_inputs= 0, */
2794         .svhs           = NO_SVHS,
2795         .gpiomask       = 0,
2796         .muxsel         = MUXSEL(2, 3),
2797         .gpiomux        = { 0 },
2798         .no_msp34xx     = 1,
2799         .pll            = PLL_28,
2800         .tuner_type     = TUNER_ABSENT,
2801         .tuner_addr = ADDR_UNSET,
2802     },
2803     /* ---- card 0xa0---------------------------------- */
2804     [BTTV_BOARD_TVT_TD3116] = {
2805         .name           = "Tongwei Video Technology TD-3116",
2806         .video_inputs   = 16,
2807         .gpiomask       = 0xc00ff,
2808         .muxsel         = MUXSEL(2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2),
2809         .muxsel_hook    = td3116_muxsel,
2810         .svhs           = NO_SVHS,
2811         .pll        = PLL_28,
2812         .tuner_type     = TUNER_ABSENT,
2813     },
2814     [BTTV_BOARD_APOSONIC_WDVR] = {
2815         .name           = "Aposonic W-DVR",
2816         .video_inputs   = 4,
2817         .svhs           = NO_SVHS,
2818         .muxsel         = MUXSEL(2, 3, 1, 0),
2819         .tuner_type     = TUNER_ABSENT,
2820     },
2821     [BTTV_BOARD_ADLINK_MPG24] = {
2822         /* Adlink MPG24 */
2823         .name           = "Adlink MPG24",
2824         .video_inputs   = 1,
2825         /* .audio_inputs= 1, */
2826         .svhs           = NO_SVHS,
2827         .muxsel         = MUXSEL(2, 2, 2, 2),
2828         .tuner_type     = UNSET,
2829         .tuner_addr = ADDR_UNSET,
2830         .pll            = PLL_28,
2831     },
2832     [BTTV_BOARD_BT848_CAP_14] = {
2833         .name       = "Bt848 Capture 14MHz",
2834         .video_inputs   = 4,
2835         .svhs       = 2,
2836         .muxsel     = MUXSEL(2, 3, 1, 0),
2837         .pll        = PLL_14,
2838         .tuner_type = TUNER_ABSENT,
2839     },
2840     [BTTV_BOARD_CYBERVISION_CV06] = {
2841         .name       = "CyberVision CV06 (SV)",
2842         .video_inputs   = 4,
2843         /* .audio_inputs= 0, */
2844         .svhs       = NO_SVHS,
2845         .muxsel     = MUXSEL(2, 3, 1, 0),
2846         .pll        = PLL_28,
2847         .tuner_type = TUNER_ABSENT,
2848         .tuner_addr = ADDR_UNSET,
2849     },
2850     [BTTV_BOARD_KWORLD_VSTREAM_XPERT] = {
2851         /* Pojar George <geoubuntu@gmail.com> */
2852         .name           = "Kworld V-Stream Xpert TV PVR878",
2853         .video_inputs   = 3,
2854         /* .audio_inputs= 1, */
2855         .svhs           = 2,
2856         .gpiomask       = 0x001c0007,
2857         .muxsel         = MUXSEL(2, 3, 1, 1),
2858         .gpiomux        = { 0, 1, 2, 2 },
2859         .gpiomute       = 3,
2860         .pll            = PLL_28,
2861         .tuner_type     = TUNER_TENA_9533_DI,
2862         .tuner_addr    = ADDR_UNSET,
2863         .has_remote     = 1,
2864         .has_radio      = 1,
2865     },
2866     /* ---- card 0xa6---------------------------------- */
2867     [BTTV_BOARD_PCI_8604PW] = {
2868         /* PCI-8604PW with special unlock sequence */
2869         .name           = "PCI-8604PW",
2870         .video_inputs   = 2,
2871         /* .audio_inputs= 0, */
2872         .svhs           = NO_SVHS,
2873         /* The second input is available on CN4, if populated.
2874          * The other 5x2 header (CN2?) connects to the same inputs
2875          * as the on-board BNCs */
2876         .muxsel         = MUXSEL(2, 3),
2877         .tuner_type     = TUNER_ABSENT,
2878         .no_msp34xx = 1,
2879         .no_tda7432 = 1,
2880         .pll            = PLL_35,
2881     },
2882 };
2883 
2884 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards);
2885 
2886 /* ----------------------------------------------------------------------- */
2887 
2888 static unsigned char eeprom_data[256];
2889 
2890 /*
2891  * identify card
2892  */
2893 void bttv_idcard(struct bttv *btv)
2894 {
2895     unsigned int gpiobits;
2896     int i,type;
2897 
2898     /* read PCI subsystem ID */
2899     btv->cardid  = btv->c.pci->subsystem_device << 16;
2900     btv->cardid |= btv->c.pci->subsystem_vendor;
2901 
2902     if (0 != btv->cardid && 0xffffffff != btv->cardid) {
2903         /* look for the card */
2904         for (type = -1, i = 0; cards[i].id != 0; i++)
2905             if (cards[i].id  == btv->cardid)
2906                 type = i;
2907 
2908         if (type != -1) {
2909             /* found it */
2910             pr_info("%d: detected: %s [card=%d], PCI subsystem ID is %04x:%04x\n",
2911                 btv->c.nr, cards[type].name, cards[type].cardnr,
2912                 btv->cardid & 0xffff,
2913                 (btv->cardid >> 16) & 0xffff);
2914             btv->c.type = cards[type].cardnr;
2915         } else {
2916             /* 404 */
2917             pr_info("%d: subsystem: %04x:%04x (UNKNOWN)\n",
2918                 btv->c.nr, btv->cardid & 0xffff,
2919                 (btv->cardid >> 16) & 0xffff);
2920             pr_debug("please mail id, board name and the correct card= insmod option to linux-media@vger.kernel.org\n");
2921         }
2922     }
2923 
2924     /* let the user override the autodetected type */
2925     if (card[btv->c.nr] < bttv_num_tvcards)
2926         btv->c.type=card[btv->c.nr];
2927 
2928     /* print which card config we are using */
2929     pr_info("%d: using: %s [card=%d,%s]\n",
2930         btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type,
2931         card[btv->c.nr] < bttv_num_tvcards
2932         ? "insmod option" : "autodetected");
2933 
2934     /* overwrite gpio stuff ?? */
2935     if (UNSET == audioall && UNSET == audiomux[0])
2936         return;
2937 
2938     if (UNSET != audiomux[0]) {
2939         gpiobits = 0;
2940         for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2941             bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i];
2942             gpiobits |= audiomux[i];
2943         }
2944     } else {
2945         gpiobits = audioall;
2946         for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2947             bttv_tvcards[btv->c.type].gpiomux[i] = audioall;
2948         }
2949     }
2950     bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits;
2951     pr_info("%d: gpio config override: mask=0x%x, mux=",
2952         btv->c.nr, bttv_tvcards[btv->c.type].gpiomask);
2953     for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
2954         pr_cont("%s0x%x",
2955             i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]);
2956     }
2957     pr_cont("\n");
2958 }
2959 
2960 /*
2961  * (most) board specific initialisations goes here
2962  */
2963 
2964 /* Some Modular Technology cards have an eeprom, but no subsystem ID */
2965 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256])
2966 {
2967     int type = -1;
2968 
2969     if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13))
2970         type = BTTV_BOARD_MODTEC_205;
2971     else if (0 == strncmp(eeprom_data+20,"Picolo",7))
2972         type = BTTV_BOARD_EURESYS_PICOLO;
2973     else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0)
2974         type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */
2975 
2976     if (-1 != type) {
2977         btv->c.type = type;
2978         pr_info("%d: detected by eeprom: %s [card=%d]\n",
2979             btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type);
2980     }
2981 }
2982 
2983 static void flyvideo_gpio(struct bttv *btv)
2984 {
2985     int gpio, has_remote, has_radio, is_capture_only;
2986     int is_lr90, has_tda9820_tda9821;
2987     int tuner_type = UNSET, ttype;
2988 
2989     gpio_inout(0xffffff, 0);
2990     udelay(8);  /* without this we would see the 0x1800 mask */
2991     gpio = gpio_read();
2992     /* FIXME: must restore OUR_EN ??? */
2993 
2994     /* all cards provide GPIO info, some have an additional eeprom
2995      * LR50: GPIO coding can be found lower right CP1 .. CP9
2996      *       CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1.
2997      *       GPIO14-12: n.c.
2998      * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878)
2999 
3000      * lowest 3 bytes are remote control codes (no handshake needed)
3001      * xxxFFF: No remote control chip soldered
3002      * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered
3003      * Note: Some bits are Audio_Mask !
3004      */
3005     ttype = (gpio & 0x0f0000) >> 16;
3006     switch (ttype) {
3007     case 0x0:
3008         tuner_type = 2;  /* NTSC, e.g. TPI8NSR11P */
3009         break;
3010     case 0x2:
3011         tuner_type = 39; /* LG NTSC (newer TAPC series) TAPC-H701P */
3012         break;
3013     case 0x4:
3014         tuner_type = 5;  /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */
3015         break;
3016     case 0x6:
3017         tuner_type = 37; /* LG PAL (newer TAPC series) TAPC-G702P */
3018         break;
3019     case 0xC:
3020         tuner_type = 3;  /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */
3021         break;
3022     default:
3023         pr_info("%d: FlyVideo_gpio: unknown tuner type\n", btv->c.nr);
3024         break;
3025     }
3026 
3027     has_remote          =   gpio & 0x800000;
3028     has_radio       =   gpio & 0x400000;
3029     /*   unknown                   0x200000;
3030      *   unknown2                  0x100000; */
3031     is_capture_only     = !(gpio & 0x008000); /* GPIO15 */
3032     has_tda9820_tda9821 = !(gpio & 0x004000);
3033     is_lr90             = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */
3034     /*
3035      * gpio & 0x001000    output bit for audio routing */
3036 
3037     if (is_capture_only)
3038         tuner_type = TUNER_ABSENT; /* No tuner present */
3039 
3040     pr_info("%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n",
3041         btv->c.nr, has_radio ? "yes" : "no",
3042         has_remote ? "yes" : "no", tuner_type, gpio);
3043     pr_info("%d: FlyVideo  LR90=%s tda9821/tda9820=%s capture_only=%s\n",
3044         btv->c.nr, is_lr90 ? "yes" : "no",
3045         has_tda9820_tda9821 ? "yes" : "no",
3046         is_capture_only ? "yes" : "no");
3047 
3048     if (tuner_type != UNSET) /* only set if known tuner autodetected, else let insmod option through */
3049         btv->tuner_type = tuner_type;
3050     btv->has_radio = has_radio;
3051 
3052     /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80
3053      * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00
3054      * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */
3055     if (has_tda9820_tda9821)
3056         btv->audio_mode_gpio = lt9415_audio;
3057     /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */
3058 }
3059 
3060 static int miro_tunermap[] = { 0,6,2,3,   4,5,6,0,  3,0,4,5,  5,2,16,1,
3061                    14,2,17,1, 4,1,4,3,  1,2,16,1, 4,4,4,4 };
3062 static int miro_fmtuner[]  = { 0,0,0,0,   0,0,0,0,  0,0,0,0,  0,0,0,1,
3063                    1,1,1,1,   1,1,1,0,  0,0,0,0,  0,1,0,0 };
3064 
3065 static void miro_pinnacle_gpio(struct bttv *btv)
3066 {
3067     int id,msp,gpio;
3068     char *info;
3069 
3070     gpio_inout(0xffffff, 0);
3071     gpio = gpio_read();
3072     id   = ((gpio>>10) & 63) -1;
3073     msp  = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx");
3074     if (id < 32) {
3075         btv->tuner_type = miro_tunermap[id];
3076         if (0 == (gpio & 0x20)) {
3077             btv->has_radio = 1;
3078             if (!miro_fmtuner[id]) {
3079                 btv->has_tea575x = 1;
3080                 btv->tea_gpio.wren = 6;
3081                 btv->tea_gpio.most = 7;
3082                 btv->tea_gpio.clk  = 8;
3083                 btv->tea_gpio.data = 9;
3084                 tea575x_init(btv);
3085             }
3086         } else {
3087             btv->has_radio = 0;
3088         }
3089         if (-1 != msp) {
3090             if (btv->c.type == BTTV_BOARD_MIRO)
3091                 btv->c.type = BTTV_BOARD_MIROPRO;
3092             if (btv->c.type == BTTV_BOARD_PINNACLE)
3093                 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3094         }
3095         pr_info("%d: miro: id=%d tuner=%d radio=%s stereo=%s\n",
3096             btv->c.nr, id+1, btv->tuner_type,
3097             !btv->has_radio ? "no" :
3098             (btv->has_tea575x ? "tea575x" : "fmtuner"),
3099             (-1 == msp) ? "no" : "yes");
3100     } else {
3101         /* new cards with microtune tuner */
3102         id = 63 - id;
3103         btv->has_radio = 0;
3104         switch (id) {
3105         case 1:
3106             info = "PAL / mono";
3107             btv->tda9887_conf = TDA9887_INTERCARRIER;
3108             break;
3109         case 2:
3110             info = "PAL+SECAM / stereo";
3111             btv->has_radio = 1;
3112             btv->tda9887_conf = TDA9887_QSS;
3113             break;
3114         case 3:
3115             info = "NTSC / stereo";
3116             btv->has_radio = 1;
3117             btv->tda9887_conf = TDA9887_QSS;
3118             break;
3119         case 4:
3120             info = "PAL+SECAM / mono";
3121             btv->tda9887_conf = TDA9887_QSS;
3122             break;
3123         case 5:
3124             info = "NTSC / mono";
3125             btv->tda9887_conf = TDA9887_INTERCARRIER;
3126             break;
3127         case 6:
3128             info = "NTSC / stereo";
3129             btv->tda9887_conf = TDA9887_INTERCARRIER;
3130             break;
3131         case 7:
3132             info = "PAL / stereo";
3133             btv->tda9887_conf = TDA9887_INTERCARRIER;
3134             break;
3135         default:
3136             info = "oops: unknown card";
3137             break;
3138         }
3139         if (-1 != msp)
3140             btv->c.type = BTTV_BOARD_PINNACLEPRO;
3141         pr_info("%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n",
3142             btv->c.nr, id, info, btv->has_radio ? "yes" : "no");
3143         btv->tuner_type = TUNER_MT2032;
3144     }
3145 }
3146 
3147 /* GPIO21   L: Buffer aktiv, H: Buffer inaktiv */
3148 #define LM1882_SYNC_DRIVE     0x200000L
3149 
3150 static void init_ids_eagle(struct bttv *btv)
3151 {
3152     gpio_inout(0xffffff,0xFFFF37);
3153     gpio_write(0x200020);
3154 
3155     /* flash strobe inverter ?! */
3156     gpio_write(0x200024);
3157 
3158     /* switch sync drive off */
3159     gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3160 
3161     /* set BT848 muxel to 2 */
3162     btaor((2)<<5, ~(2<<5), BT848_IFORM);
3163 }
3164 
3165 /* Muxsel helper for the IDS Eagle.
3166  * the eagles does not use the standard muxsel-bits but
3167  * has its own multiplexer */
3168 static void eagle_muxsel(struct bttv *btv, unsigned int input)
3169 {
3170     gpio_bits(3, input & 3);
3171 
3172     /* composite */
3173     /* set chroma ADC to sleep */
3174     btor(BT848_ADC_C_SLEEP, BT848_ADC);
3175     /* set to composite video */
3176     btand(~BT848_CONTROL_COMP, BT848_E_CONTROL);
3177     btand(~BT848_CONTROL_COMP, BT848_O_CONTROL);
3178 
3179     /* switch sync drive off */
3180     gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3181 }
3182 
3183 static void gvc1100_muxsel(struct bttv *btv, unsigned int input)
3184 {
3185     static const int masks[] = {0x30, 0x01, 0x12, 0x23};
3186     gpio_write(masks[input%4]);
3187 }
3188 
3189 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and
3190    alarms output
3191 
3192    GPIObit    | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
3193    assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1|   |   |
3194 
3195    IN - sensor inputs, INx - sensor inputs and TI XORed together
3196    O1,O2,O3 - alarm outputs (relays)
3197 
3198    OUT ENABLE   1    1   0  . 1  1   0   0 . 0   0   0    0   = 0x6C0
3199 
3200 */
3201 
3202 static void init_lmlbt4x(struct bttv *btv)
3203 {
3204     pr_debug("LMLBT4x init\n");
3205     btwrite(0x000000, BT848_GPIO_REG_INP);
3206     gpio_inout(0xffffff, 0x0006C0);
3207     gpio_write(0x000000);
3208 }
3209 
3210 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input)
3211 {
3212     unsigned int inmux = input % 8;
3213     gpio_inout( 0xf, 0xf );
3214     gpio_bits( 0xf, inmux );
3215 }
3216 
3217 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input)
3218 {
3219     unsigned int inmux = input % 4;
3220     gpio_inout( 3<<9, 3<<9 );
3221     gpio_bits( 3<<9, inmux<<9 );
3222 }
3223 
3224 static void geovision_muxsel(struct bttv *btv, unsigned int input)
3225 {
3226     unsigned int inmux = input % 16;
3227     gpio_inout(0xf, 0xf);
3228     gpio_bits(0xf, inmux);
3229 }
3230 
3231 /*
3232  * The TD3116 has 2 74HC4051 muxes wired to the MUX0 input of a bt878.
3233  * The first 74HC4051 has the lower 8 inputs, the second one the higher 8.
3234  * The muxes are controlled via a 74HC373 latch which is connected to
3235  * GPIOs 0-7. GPIO 18 is connected to the LE signal of the latch.
3236  * Q0 of the latch is connected to the Enable (~E) input of the first
3237  * 74HC4051. Q1 - Q3 are connected to S0 - S2 of the same 74HC4051.
3238  * Q4 - Q7 are connected to the second 74HC4051 in the same way.
3239  */
3240 
3241 static void td3116_latch_value(struct bttv *btv, u32 value)
3242 {
3243     gpio_bits((1<<18) | 0xff, value);
3244     gpio_bits((1<<18) | 0xff, (1<<18) | value);
3245     udelay(1);
3246     gpio_bits((1<<18) | 0xff, value);
3247 }
3248 
3249 static void td3116_muxsel(struct bttv *btv, unsigned int input)
3250 {
3251     u32 value;
3252     u32 highbit;
3253 
3254     highbit = (input & 0x8) >> 3 ;
3255 
3256     /* Disable outputs and set value in the mux */
3257     value = 0x11; /* Disable outputs */
3258     value |= ((input & 0x7) << 1)  << (4 * highbit);
3259     td3116_latch_value(btv, value);
3260 
3261     /* Enable the correct output */
3262     value &= ~0x11;
3263     value |= ((highbit ^ 0x1) << 4) | highbit;
3264     td3116_latch_value(btv, value);
3265 }
3266 
3267 /* ----------------------------------------------------------------------- */
3268 
3269 static void bttv_reset_audio(struct bttv *btv)
3270 {
3271     /*
3272      * BT878A has a audio-reset register.
3273      * 1. This register is an audio reset function but it is in
3274      *    function-0 (video capture) address space.
3275      * 2. It is enough to do this once per power-up of the card.
3276      * 3. There is a typo in the Conexant doc -- it is not at
3277      *    0x5B, but at 0x058. (B is an odd-number, obviously a typo!).
3278      * --//Shrikumar 030609
3279      */
3280     if (btv->id != 878)
3281         return;
3282 
3283     if (bttv_debug)
3284         pr_debug("%d: BT878A ARESET\n", btv->c.nr);
3285     btwrite((1<<7), 0x058);
3286     udelay(10);
3287     btwrite(     0, 0x058);
3288 }
3289 
3290 /* initialization part one -- before registering i2c bus */
3291 void bttv_init_card1(struct bttv *btv)
3292 {
3293     switch (btv->c.type) {
3294     case BTTV_BOARD_HAUPPAUGE:
3295     case BTTV_BOARD_HAUPPAUGE878:
3296         boot_msp34xx(btv,5);
3297         break;
3298     case BTTV_BOARD_VOODOOTV_200:
3299     case BTTV_BOARD_VOODOOTV_FM:
3300         boot_msp34xx(btv,20);
3301         break;
3302     case BTTV_BOARD_AVERMEDIA98:
3303         boot_msp34xx(btv,11);
3304         break;
3305     case BTTV_BOARD_HAUPPAUGEPVR:
3306         pvr_boot(btv);
3307         break;
3308     case BTTV_BOARD_TWINHAN_DST:
3309     case BTTV_BOARD_AVDVBT_771:
3310     case BTTV_BOARD_PINNACLESAT:
3311         btv->use_i2c_hw = 1;
3312         break;
3313     case BTTV_BOARD_ADLINK_RTV24:
3314         init_RTV24( btv );
3315         break;
3316     case BTTV_BOARD_PCI_8604PW:
3317         init_PCI8604PW(btv);
3318         break;
3319 
3320     }
3321     if (!bttv_tvcards[btv->c.type].has_dvb)
3322         bttv_reset_audio(btv);
3323 }
3324 
3325 /* initialization part two -- after registering i2c bus */
3326 void bttv_init_card2(struct bttv *btv)
3327 {
3328     btv->tuner_type = UNSET;
3329 
3330     if (BTTV_BOARD_UNKNOWN == btv->c.type) {
3331         bttv_readee(btv,eeprom_data,0xa0);
3332         identify_by_eeprom(btv,eeprom_data);
3333     }
3334 
3335     switch (btv->c.type) {
3336     case BTTV_BOARD_MIRO:
3337     case BTTV_BOARD_MIROPRO:
3338     case BTTV_BOARD_PINNACLE:
3339     case BTTV_BOARD_PINNACLEPRO:
3340         /* miro/pinnacle */
3341         miro_pinnacle_gpio(btv);
3342         break;
3343     case BTTV_BOARD_FLYVIDEO_98:
3344     case BTTV_BOARD_MAXI:
3345     case BTTV_BOARD_LIFE_FLYKIT:
3346     case BTTV_BOARD_FLYVIDEO:
3347     case BTTV_BOARD_TYPHOON_TVIEW:
3348     case BTTV_BOARD_CHRONOS_VS2:
3349     case BTTV_BOARD_FLYVIDEO_98FM:
3350     case BTTV_BOARD_FLYVIDEO2000:
3351     case BTTV_BOARD_FLYVIDEO98EZ:
3352     case BTTV_BOARD_CONFERENCETV:
3353     case BTTV_BOARD_LIFETEC_9415:
3354         flyvideo_gpio(btv);
3355         break;
3356     case BTTV_BOARD_HAUPPAUGE:
3357     case BTTV_BOARD_HAUPPAUGE878:
3358     case BTTV_BOARD_HAUPPAUGEPVR:
3359         /* pick up some config infos from the eeprom */
3360         bttv_readee(btv,eeprom_data,0xa0);
3361         hauppauge_eeprom(btv);
3362         break;
3363     case BTTV_BOARD_AVERMEDIA98:
3364     case BTTV_BOARD_AVPHONE98:
3365         bttv_readee(btv,eeprom_data,0xa0);
3366         avermedia_eeprom(btv);
3367         break;
3368     case BTTV_BOARD_PXC200:
3369         init_PXC200(btv);
3370         break;
3371     case BTTV_BOARD_PICOLO_TETRA_CHIP:
3372         picolo_tetra_init(btv);
3373         break;
3374     case BTTV_BOARD_VHX:
3375         btv->has_radio    = 1;
3376         btv->has_tea575x  = 1;
3377         btv->tea_gpio.wren = 5;
3378         btv->tea_gpio.most = 6;
3379         btv->tea_gpio.clk  = 3;
3380         btv->tea_gpio.data = 4;
3381         tea575x_init(btv);
3382         break;
3383     case BTTV_BOARD_VOBIS_BOOSTAR:
3384     case BTTV_BOARD_TERRATV:
3385         terratec_active_radio_upgrade(btv);
3386         break;
3387     case BTTV_BOARD_MAGICTVIEW061:
3388         if (btv->cardid == 0x3002144f) {
3389             btv->has_radio=1;
3390             pr_info("%d: radio detected by subsystem id (CPH05x)\n",
3391                 btv->c.nr);
3392         }
3393         break;
3394     case BTTV_BOARD_STB2:
3395         if (btv->cardid == 0x3060121a) {
3396             /* Fix up entry for 3DFX VoodooTV 100,
3397                which is an OEM STB card variant. */
3398             btv->has_radio=0;
3399             btv->tuner_type=TUNER_TEMIC_NTSC;
3400         }
3401         break;
3402     case BTTV_BOARD_OSPREY1x0:
3403     case BTTV_BOARD_OSPREY1x0_848:
3404     case BTTV_BOARD_OSPREY101_848:
3405     case BTTV_BOARD_OSPREY1x1:
3406     case BTTV_BOARD_OSPREY1x1_SVID:
3407     case BTTV_BOARD_OSPREY2xx:
3408     case BTTV_BOARD_OSPREY2x0_SVID:
3409     case BTTV_BOARD_OSPREY2x0:
3410     case BTTV_BOARD_OSPREY440:
3411     case BTTV_BOARD_OSPREY500:
3412     case BTTV_BOARD_OSPREY540:
3413     case BTTV_BOARD_OSPREY2000:
3414         bttv_readee(btv,eeprom_data,0xa0);
3415         osprey_eeprom(btv, eeprom_data);
3416         break;
3417     case BTTV_BOARD_IDS_EAGLE:
3418         init_ids_eagle(btv);
3419         break;
3420     case BTTV_BOARD_MODTEC_205:
3421         bttv_readee(btv,eeprom_data,0xa0);
3422         modtec_eeprom(btv);
3423         break;
3424     case BTTV_BOARD_LMLBT4:
3425         init_lmlbt4x(btv);
3426         break;
3427     case BTTV_BOARD_TIBET_CS16:
3428         tibetCS16_init(btv);
3429         break;
3430     case BTTV_BOARD_KODICOM_4400R:
3431         kodicom4400r_init(btv);
3432         break;
3433     case BTTV_BOARD_GEOVISION_GV800S:
3434         gv800s_init(btv);
3435         break;
3436     }
3437 
3438     /* pll configuration */
3439     if (!(btv->id==848 && btv->revision==0x11)) {
3440         /* defaults from card list */
3441         if (PLL_28 == bttv_tvcards[btv->c.type].pll) {
3442             btv->pll.pll_ifreq=28636363;
3443             btv->pll.pll_crystal=BT848_IFORM_XT0;
3444         }
3445         if (PLL_35 == bttv_tvcards[btv->c.type].pll) {
3446             btv->pll.pll_ifreq=35468950;
3447             btv->pll.pll_crystal=BT848_IFORM_XT1;
3448         }
3449         if (PLL_14 == bttv_tvcards[btv->c.type].pll) {
3450             btv->pll.pll_ifreq = 14318181;
3451             btv->pll.pll_crystal = BT848_IFORM_XT0;
3452         }
3453         /* insmod options can override */
3454         switch (pll[btv->c.nr]) {
3455         case 0: /* none */
3456             btv->pll.pll_crystal = 0;
3457             btv->pll.pll_ifreq   = 0;
3458             btv->pll.pll_ofreq   = 0;
3459             break;
3460         case 1: /* 28 MHz */
3461         case 28:
3462             btv->pll.pll_ifreq   = 28636363;
3463             btv->pll.pll_ofreq   = 0;
3464             btv->pll.pll_crystal = BT848_IFORM_XT0;
3465             break;
3466         case 2: /* 35 MHz */
3467         case 35:
3468             btv->pll.pll_ifreq   = 35468950;
3469             btv->pll.pll_ofreq   = 0;
3470             btv->pll.pll_crystal = BT848_IFORM_XT1;
3471             break;
3472         case 3: /* 14 MHz */
3473         case 14:
3474             btv->pll.pll_ifreq   = 14318181;
3475             btv->pll.pll_ofreq   = 0;
3476             btv->pll.pll_crystal = BT848_IFORM_XT0;
3477             break;
3478         }
3479     }
3480     btv->pll.pll_current = -1;
3481 
3482     /* tuner configuration (from card list / autodetect / insmod option) */
3483     if (UNSET != bttv_tvcards[btv->c.type].tuner_type)
3484         if (UNSET == btv->tuner_type)
3485             btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type;
3486     if (UNSET != tuner[btv->c.nr])
3487         btv->tuner_type = tuner[btv->c.nr];
3488 
3489     if (btv->tuner_type == TUNER_ABSENT)
3490         pr_info("%d: tuner absent\n", btv->c.nr);
3491     else if (btv->tuner_type == UNSET)
3492         pr_warn("%d: tuner type unset\n", btv->c.nr);
3493     else
3494         pr_info("%d: tuner type=%d\n", btv->c.nr, btv->tuner_type);
3495 
3496     if (autoload != UNSET) {
3497         pr_warn("%d: the autoload option is obsolete\n", btv->c.nr);
3498         pr_warn("%d: use option msp3400, tda7432 or tvaudio to override which audio module should be used\n",
3499             btv->c.nr);
3500     }
3501 
3502     if (UNSET == btv->tuner_type)
3503         btv->tuner_type = TUNER_ABSENT;
3504 
3505     btv->dig = bttv_tvcards[btv->c.type].has_dig_in ?
3506            bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET;
3507     btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ?
3508             UNSET : bttv_tvcards[btv->c.type].svhs;
3509     if (svhs[btv->c.nr] != UNSET)
3510         btv->svhs = svhs[btv->c.nr];
3511     if (remote[btv->c.nr] != UNSET)
3512         btv->has_remote = remote[btv->c.nr];
3513 
3514     if (bttv_tvcards[btv->c.type].has_radio)
3515         btv->has_radio = 1;
3516     if (bttv_tvcards[btv->c.type].has_remote)
3517         btv->has_remote = 1;
3518     if (!bttv_tvcards[btv->c.type].no_gpioirq)
3519         btv->gpioirq = 1;
3520     if (bttv_tvcards[btv->c.type].volume_gpio)
3521         btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio;
3522     if (bttv_tvcards[btv->c.type].audio_mode_gpio)
3523         btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio;
3524 
3525     if (btv->tuner_type == TUNER_ABSENT)
3526         return;  /* no tuner or related drivers to load */
3527 
3528     if (btv->has_saa6588 || saa6588[btv->c.nr]) {
3529         /* Probe for RDS receiver chip */
3530         static const unsigned short addrs[] = {
3531             0x20 >> 1,
3532             0x22 >> 1,
3533             I2C_CLIENT_END
3534         };
3535         struct v4l2_subdev *sd;
3536 
3537         sd = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3538             &btv->c.i2c_adap, "saa6588", 0, addrs);
3539         btv->has_saa6588 = (sd != NULL);
3540     }
3541 
3542     /* try to detect audio/fader chips */
3543 
3544     /* First check if the user specified the audio chip via a module
3545        option. */
3546 
3547     switch (audiodev[btv->c.nr]) {
3548     case -1:
3549         return; /* do not load any audio module */
3550 
3551     case 0: /* autodetect */
3552         break;
3553 
3554     case 1: {
3555         /* The user specified that we should probe for msp3400 */
3556         static const unsigned short addrs[] = {
3557             I2C_ADDR_MSP3400 >> 1,
3558             I2C_ADDR_MSP3400_ALT >> 1,
3559             I2C_CLIENT_END
3560         };
3561 
3562         btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3563             &btv->c.i2c_adap, "msp3400", 0, addrs);
3564         if (btv->sd_msp34xx)
3565             return;
3566         goto no_audio;
3567     }
3568 
3569     case 2: {
3570         /* The user specified that we should probe for tda7432 */
3571         static const unsigned short addrs[] = {
3572             I2C_ADDR_TDA7432 >> 1,
3573             I2C_CLIENT_END
3574         };
3575 
3576         if (v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3577                 &btv->c.i2c_adap, "tda7432", 0, addrs))
3578             return;
3579         goto no_audio;
3580     }
3581 
3582     case 3: {
3583         /* The user specified that we should probe for tvaudio */
3584         btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3585             &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3586         if (btv->sd_tvaudio)
3587             return;
3588         goto no_audio;
3589     }
3590 
3591     default:
3592         pr_warn("%d: unknown audiodev value!\n", btv->c.nr);
3593         return;
3594     }
3595 
3596     /* There were no overrides, so now we try to discover this through the
3597        card definition */
3598 
3599     /* probe for msp3400 first: this driver can detect whether or not
3600        it really is a msp3400, so it will return NULL when the device
3601        found is really something else (e.g. a tea6300). */
3602     if (!bttv_tvcards[btv->c.type].no_msp34xx) {
3603         btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3604             &btv->c.i2c_adap, "msp3400",
3605             0, I2C_ADDRS(I2C_ADDR_MSP3400 >> 1));
3606     } else if (bttv_tvcards[btv->c.type].msp34xx_alt) {
3607         btv->sd_msp34xx = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3608             &btv->c.i2c_adap, "msp3400",
3609             0, I2C_ADDRS(I2C_ADDR_MSP3400_ALT >> 1));
3610     }
3611 
3612     /* If we found a msp34xx, then we're done. */
3613     if (btv->sd_msp34xx)
3614         return;
3615 
3616     /* Now see if we can find one of the tvaudio devices. */
3617     btv->sd_tvaudio = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3618         &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3619     if (btv->sd_tvaudio) {
3620         /* There may be two tvaudio chips on the card, so try to
3621            find another. */
3622         v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3623             &btv->c.i2c_adap, "tvaudio", 0, tvaudio_addrs());
3624     }
3625 
3626     /* it might also be a tda7432. */
3627     if (!bttv_tvcards[btv->c.type].no_tda7432) {
3628         static const unsigned short addrs[] = {
3629             I2C_ADDR_TDA7432 >> 1,
3630             I2C_CLIENT_END
3631         };
3632 
3633         btv->sd_tda7432 = v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3634                 &btv->c.i2c_adap, "tda7432", 0, addrs);
3635         if (btv->sd_tda7432)
3636             return;
3637     }
3638     if (btv->sd_tvaudio)
3639         return;
3640 
3641 no_audio:
3642     pr_warn("%d: audio absent, no audio device found!\n", btv->c.nr);
3643 }
3644 
3645 
3646 /* initialize the tuner */
3647 void bttv_init_tuner(struct bttv *btv)
3648 {
3649     int addr = ADDR_UNSET;
3650 
3651     if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr)
3652         addr = bttv_tvcards[btv->c.type].tuner_addr;
3653 
3654     if (btv->tuner_type != TUNER_ABSENT) {
3655         struct tuner_setup tun_setup;
3656 
3657         /* Load tuner module before issuing tuner config call! */
3658         if (btv->has_radio)
3659             v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3660                 &btv->c.i2c_adap, "tuner",
3661                 0, v4l2_i2c_tuner_addrs(ADDRS_RADIO));
3662         v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3663                 &btv->c.i2c_adap, "tuner",
3664                 0, v4l2_i2c_tuner_addrs(ADDRS_DEMOD));
3665         v4l2_i2c_new_subdev(&btv->c.v4l2_dev,
3666                 &btv->c.i2c_adap, "tuner",
3667                 0, v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD));
3668 
3669         tun_setup.mode_mask = T_ANALOG_TV;
3670         tun_setup.type = btv->tuner_type;
3671         tun_setup.addr = addr;
3672 
3673         if (btv->has_radio)
3674             tun_setup.mode_mask |= T_RADIO;
3675 
3676         bttv_call_all(btv, tuner, s_type_addr, &tun_setup);
3677     }
3678 
3679     if (btv->tda9887_conf) {
3680         struct v4l2_priv_tun_config tda9887_cfg;
3681 
3682         tda9887_cfg.tuner = TUNER_TDA9887;
3683         tda9887_cfg.priv = &btv->tda9887_conf;
3684 
3685         bttv_call_all(btv, tuner, s_config, &tda9887_cfg);
3686     }
3687 }
3688 
3689 /* ----------------------------------------------------------------------- */
3690 
3691 static void modtec_eeprom(struct bttv *btv)
3692 {
3693     if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) {
3694         btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I;
3695         pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3696             btv->c.nr, &eeprom_data[0x1e]);
3697     } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) {
3698         btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I;
3699         pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3700             btv->c.nr, &eeprom_data[0x1e]);
3701     } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) {
3702         btv->tuner_type=TUNER_PHILIPS_NTSC;
3703         pr_info("%d: Modtec: Tuner autodetected by eeprom: %s\n",
3704             btv->c.nr, &eeprom_data[0x1e]);
3705     } else {
3706         pr_info("%d: Modtec: Unknown TunerString: %s\n",
3707             btv->c.nr, &eeprom_data[0x1e]);
3708     }
3709 }
3710 
3711 static void hauppauge_eeprom(struct bttv *btv)
3712 {
3713     struct tveeprom tv;
3714 
3715     tveeprom_hauppauge_analog(&tv, eeprom_data);
3716     btv->tuner_type = tv.tuner_type;
3717     btv->has_radio  = tv.has_radio;
3718 
3719     pr_info("%d: Hauppauge eeprom indicates model#%d\n",
3720         btv->c.nr, tv.model);
3721 
3722     /*
3723      * Some of the 878 boards have duplicate PCI IDs. Switch the board
3724      * type based on model #.
3725      */
3726     if(tv.model == 64900) {
3727         pr_info("%d: Switching board type from %s to %s\n",
3728             btv->c.nr,
3729             bttv_tvcards[btv->c.type].name,
3730             bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name);
3731         btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB;
3732     }
3733 
3734     /* The 61334 needs the msp3410 to do the radio demod to get sound */
3735     if (tv.model == 61334)
3736         btv->radio_uses_msp_demodulator = 1;
3737 }
3738 
3739 /* ----------------------------------------------------------------------- */
3740 
3741 static void bttv_tea575x_set_pins(struct snd_tea575x *tea, u8 pins)
3742 {
3743     struct bttv *btv = tea->private_data;
3744     struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3745     u16 val = 0;
3746 
3747     val |= (pins & TEA575X_DATA) ? (1 << gpio.data) : 0;
3748     val |= (pins & TEA575X_CLK)  ? (1 << gpio.clk)  : 0;
3749     val |= (pins & TEA575X_WREN) ? (1 << gpio.wren) : 0;
3750 
3751     gpio_bits((1 << gpio.data) | (1 << gpio.clk) | (1 << gpio.wren), val);
3752     if (btv->mbox_ior) {
3753         /* IOW and CSEL active */
3754         gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
3755         udelay(5);
3756         /* all inactive */
3757         gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
3758               btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
3759     }
3760 }
3761 
3762 static u8 bttv_tea575x_get_pins(struct snd_tea575x *tea)
3763 {
3764     struct bttv *btv = tea->private_data;
3765     struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3766     u8 ret = 0;
3767     u16 val;
3768 
3769     if (btv->mbox_ior) {
3770         /* IOR and CSEL active */
3771         gpio_bits(btv->mbox_ior | btv->mbox_csel, 0);
3772         udelay(5);
3773     }
3774     val = gpio_read();
3775     if (btv->mbox_ior) {
3776         /* all inactive */
3777         gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
3778               btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
3779     }
3780 
3781     if (val & (1 << gpio.data))
3782         ret |= TEA575X_DATA;
3783     if (val & (1 << gpio.most))
3784         ret |= TEA575X_MOST;
3785 
3786     return ret;
3787 }
3788 
3789 static void bttv_tea575x_set_direction(struct snd_tea575x *tea, bool output)
3790 {
3791     struct bttv *btv = tea->private_data;
3792     struct bttv_tea575x_gpio gpio = btv->tea_gpio;
3793     u32 mask = (1 << gpio.clk) | (1 << gpio.wren) | (1 << gpio.data) |
3794            (1 << gpio.most);
3795 
3796     if (output)
3797         gpio_inout(mask, (1 << gpio.data) | (1 << gpio.clk) |
3798                  (1 << gpio.wren));
3799     else
3800         gpio_inout(mask, (1 << gpio.clk) | (1 << gpio.wren));
3801 }
3802 
3803 static const struct snd_tea575x_ops bttv_tea_ops = {
3804     .set_pins = bttv_tea575x_set_pins,
3805     .get_pins = bttv_tea575x_get_pins,
3806     .set_direction = bttv_tea575x_set_direction,
3807 };
3808 
3809 static int tea575x_init(struct bttv *btv)
3810 {
3811     btv->tea.private_data = btv;
3812     btv->tea.ops = &bttv_tea_ops;
3813     if (!snd_tea575x_hw_init(&btv->tea)) {
3814         pr_info("%d: detected TEA575x radio\n", btv->c.nr);
3815         btv->tea.mute = false;
3816         return 0;
3817     }
3818 
3819     btv->has_tea575x = 0;
3820     btv->has_radio = 0;
3821 
3822     return -ENODEV;
3823 }
3824 
3825 /* ----------------------------------------------------------------------- */
3826 
3827 static int terratec_active_radio_upgrade(struct bttv *btv)
3828 {
3829     btv->has_radio    = 1;
3830     btv->has_tea575x  = 1;
3831     btv->tea_gpio.wren = 4;
3832     btv->tea_gpio.most = 5;
3833     btv->tea_gpio.clk  = 3;
3834     btv->tea_gpio.data = 2;
3835 
3836     btv->mbox_iow     = 1 <<  8;
3837     btv->mbox_ior     = 1 <<  9;
3838     btv->mbox_csel    = 1 << 10;
3839 
3840     if (!tea575x_init(btv)) {
3841         pr_info("%d: Terratec Active Radio Upgrade found\n", btv->c.nr);
3842         btv->has_saa6588 = 1;
3843     }
3844 
3845     return 0;
3846 }
3847 
3848 
3849 /* ----------------------------------------------------------------------- */
3850 
3851 /*
3852  * minimal bootstrap for the WinTV/PVR -- upload altera firmware.
3853  *
3854  * The hcwamc.rbf firmware file is on the Hauppauge driver CD.  Have
3855  * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be
3856  * unpacked with unzip).
3857  */
3858 #define PVR_GPIO_DELAY      10
3859 
3860 #define BTTV_ALT_DATA       0x000001
3861 #define BTTV_ALT_DCLK       0x100000
3862 #define BTTV_ALT_NCONFIG    0x800000
3863 
3864 static int pvr_altera_load(struct bttv *btv, const u8 *micro, u32 microlen)
3865 {
3866     u32 n;
3867     u8 bits;
3868     int i;
3869 
3870     gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG);
3871     gpio_write(0);
3872     udelay(PVR_GPIO_DELAY);
3873 
3874     gpio_write(BTTV_ALT_NCONFIG);
3875     udelay(PVR_GPIO_DELAY);
3876 
3877     for (n = 0; n < microlen; n++) {
3878         bits = micro[n];
3879         for (i = 0 ; i < 8 ; i++) {
3880             gpio_bits(BTTV_ALT_DCLK,0);
3881             if (bits & 0x01)
3882                 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA);
3883             else
3884                 gpio_bits(BTTV_ALT_DATA,0);
3885             gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3886             bits >>= 1;
3887         }
3888     }
3889     gpio_bits(BTTV_ALT_DCLK,0);
3890     udelay(PVR_GPIO_DELAY);
3891 
3892     /* begin Altera init loop (Not necessary,but doesn't hurt) */
3893     for (i = 0 ; i < 30 ; i++) {
3894         gpio_bits(BTTV_ALT_DCLK,0);
3895         gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3896     }
3897     gpio_bits(BTTV_ALT_DCLK,0);
3898     return 0;
3899 }
3900 
3901 static int pvr_boot(struct bttv *btv)
3902 {
3903     const struct firmware *fw_entry;
3904     int rc;
3905 
3906     rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev);
3907     if (rc != 0) {
3908         pr_warn("%d: no altera firmware [via hotplug]\n", btv->c.nr);
3909         return rc;
3910     }
3911     rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size);
3912     pr_info("%d: altera firmware upload %s\n",
3913         btv->c.nr, (rc < 0) ? "failed" : "ok");
3914     release_firmware(fw_entry);
3915     return rc;
3916 }
3917 
3918 /* ----------------------------------------------------------------------- */
3919 /* some osprey specific stuff                                              */
3920 
3921 static void osprey_eeprom(struct bttv *btv, const u8 ee[256])
3922 {
3923     int i;
3924     u32 serial = 0;
3925     int cardid = -1;
3926 
3927     /* This code will never actually get called in this case.... */
3928     if (btv->c.type == BTTV_BOARD_UNKNOWN) {
3929         /* this might be an antique... check for MMAC label in eeprom */
3930         if (!strncmp(ee, "MMAC", 4)) {
3931             u8 checksum = 0;
3932             for (i = 0; i < 21; i++)
3933                 checksum += ee[i];
3934             if (checksum != ee[21])
3935                 return;
3936             cardid = BTTV_BOARD_OSPREY1x0_848;
3937             for (i = 12; i < 21; i++) {
3938                 serial *= 10;
3939                 serial += ee[i] - '0';
3940             }
3941         }
3942     } else {
3943         unsigned short type;
3944 
3945         for (i = 4 * 16; i < 8 * 16; i += 16) {
3946             u16 checksum = (__force u16)ip_compute_csum(ee + i, 16);
3947 
3948             if ((checksum & 0xff) + (checksum >> 8) == 0xff)
3949                 break;
3950         }
3951         if (i >= 8*16)
3952             return;
3953         ee += i;
3954 
3955         /* found a valid descriptor */
3956         type = get_unaligned_be16((__be16 *)(ee+4));
3957 
3958         switch(type) {
3959         /* 848 based */
3960         case 0x0004:
3961             cardid = BTTV_BOARD_OSPREY1x0_848;
3962             break;
3963         case 0x0005:
3964             cardid = BTTV_BOARD_OSPREY101_848;
3965             break;
3966 
3967         /* 878 based */
3968         case 0x0012:
3969         case 0x0013:
3970             cardid = BTTV_BOARD_OSPREY1x0;
3971             break;
3972         case 0x0014:
3973         case 0x0015:
3974             cardid = BTTV_BOARD_OSPREY1x1;
3975             break;
3976         case 0x0016:
3977         case 0x0017:
3978         case 0x0020:
3979             cardid = BTTV_BOARD_OSPREY1x1_SVID;
3980             break;
3981         case 0x0018:
3982         case 0x0019:
3983         case 0x001E:
3984         case 0x001F:
3985             cardid = BTTV_BOARD_OSPREY2xx;
3986             break;
3987         case 0x001A:
3988         case 0x001B:
3989             cardid = BTTV_BOARD_OSPREY2x0_SVID;
3990             break;
3991         case 0x0040:
3992             cardid = BTTV_BOARD_OSPREY500;
3993             break;
3994         case 0x0050:
3995         case 0x0056:
3996             cardid = BTTV_BOARD_OSPREY540;
3997             /* bttv_osprey_540_init(btv); */
3998             break;
3999         case 0x0060:
4000         case 0x0070:
4001         case 0x00A0:
4002             cardid = BTTV_BOARD_OSPREY2x0;
4003             /* enable output on select control lines */
4004             gpio_inout(0xffffff,0x000303);
4005             break;
4006         case 0x00D8:
4007             cardid = BTTV_BOARD_OSPREY440;
4008             break;
4009         default:
4010             /* unknown...leave generic, but get serial # */
4011             pr_info("%d: osprey eeprom: unknown card type 0x%04x\n",
4012                 btv->c.nr, type);
4013             break;
4014         }
4015         serial = get_unaligned_be32((__be32 *)(ee+6));
4016     }
4017 
4018     pr_info("%d: osprey eeprom: card=%d '%s' serial=%u\n",
4019         btv->c.nr, cardid,
4020         cardid > 0 ? bttv_tvcards[cardid].name : "Unknown", serial);
4021 
4022     if (cardid<0 || btv->c.type == cardid)
4023         return;
4024 
4025     /* card type isn't set correctly */
4026     if (card[btv->c.nr] < bttv_num_tvcards) {
4027         pr_warn("%d: osprey eeprom: Not overriding user specified card type\n",
4028             btv->c.nr);
4029     } else {
4030         pr_info("%d: osprey eeprom: Changing card type from %d to %d\n",
4031             btv->c.nr, btv->c.type, cardid);
4032         btv->c.type = cardid;
4033     }
4034 }
4035 
4036 /* ----------------------------------------------------------------------- */
4037 /* AVermedia specific stuff, from  bktr_card.c                             */
4038 
4039 static int tuner_0_table[] = {
4040     TUNER_PHILIPS_NTSC,  TUNER_PHILIPS_PAL /* PAL-BG*/,
4041     TUNER_PHILIPS_PAL,   TUNER_PHILIPS_PAL /* PAL-I*/,
4042     TUNER_PHILIPS_PAL,   TUNER_PHILIPS_PAL,
4043     TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM,
4044     TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL,
4045     TUNER_PHILIPS_FM1216ME_MK3 };
4046 
4047 static int tuner_1_table[] = {
4048     TUNER_TEMIC_NTSC,  TUNER_TEMIC_PAL,
4049     TUNER_TEMIC_PAL,   TUNER_TEMIC_PAL,
4050     TUNER_TEMIC_PAL,   TUNER_TEMIC_PAL,
4051     TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */
4052     TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL};
4053 
4054 static void avermedia_eeprom(struct bttv *btv)
4055 {
4056     int tuner_make, tuner_tv_fm, tuner_format, tuner_type = 0;
4057 
4058     tuner_make      = (eeprom_data[0x41] & 0x7);
4059     tuner_tv_fm     = (eeprom_data[0x41] & 0x18) >> 3;
4060     tuner_format    = (eeprom_data[0x42] & 0xf0) >> 4;
4061     btv->has_remote = (eeprom_data[0x42] & 0x01);
4062 
4063     if (tuner_make == 0 || tuner_make == 2)
4064         if (tuner_format <= 0x0a)
4065             tuner_type = tuner_0_table[tuner_format];
4066     if (tuner_make == 1)
4067         if (tuner_format <= 9)
4068             tuner_type = tuner_1_table[tuner_format];
4069 
4070     if (tuner_make == 4)
4071         if (tuner_format == 0x09)
4072             tuner_type = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */
4073 
4074     pr_info("%d: Avermedia eeprom[0x%02x%02x]: tuner=",
4075         btv->c.nr, eeprom_data[0x41], eeprom_data[0x42]);
4076     if (tuner_type) {
4077         btv->tuner_type = tuner_type;
4078         pr_cont("%d", tuner_type);
4079     } else
4080         pr_cont("Unknown type");
4081     pr_cont(" radio:%s remote control:%s\n",
4082            tuner_tv_fm     ? "yes" : "no",
4083            btv->has_remote ? "yes" : "no");
4084 }
4085 
4086 /*
4087  * For Voodoo TV/FM and Voodoo 200.  These cards' tuners use a TDA9880
4088  * analog demod, which is not I2C controlled like the newer and more common
4089  * TDA9887 series.  Instead it has two tri-state input pins, S0 and S1,
4090  * that control the IF for the video and audio.  Apparently, bttv GPIO
4091  * 0x10000 is connected to S0.  S0 low selects a 38.9 MHz VIF for B/G/D/K/I
4092  * (i.e., PAL) while high selects 45.75 MHz for M/N (i.e., NTSC).
4093  */
4094 u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits)
4095 {
4096 
4097     if (btv->audio_input == TVAUDIO_INPUT_TUNER) {
4098         if (bttv_tvnorms[btv->tvnorm].v4l2_id & V4L2_STD_MN)
4099             gpiobits |= 0x10000;
4100         else
4101             gpiobits &= ~0x10000;
4102     }
4103 
4104     gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpiobits);
4105     return gpiobits;
4106 }
4107 
4108 
4109 /*
4110  * reset/enable the MSP on some Hauppauge cards
4111  * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)!
4112  *
4113  * Hauppauge:  pin  5
4114  * Voodoo:     pin 20
4115  */
4116 static void boot_msp34xx(struct bttv *btv, int pin)
4117 {
4118     int mask = (1 << pin);
4119 
4120     gpio_inout(mask,mask);
4121     gpio_bits(mask,0);
4122     mdelay(2);
4123     udelay(500);
4124     gpio_bits(mask,mask);
4125 
4126     if (bttv_gpio)
4127         bttv_gpio_tracking(btv,"msp34xx");
4128     if (bttv_verbose)
4129         pr_info("%d: Hauppauge/Voodoo msp34xx: reset line init [%d]\n",
4130             btv->c.nr, pin);
4131 }
4132 
4133 /* ----------------------------------------------------------------------- */
4134 /*  Imagenation L-Model PXC200 Framegrabber */
4135 /*  This is basically the same procedure as
4136  *  used by Alessandro Rubini in his pxc200
4137  *  driver, but using BTTV functions */
4138 
4139 static void init_PXC200(struct bttv *btv)
4140 {
4141     static int vals[] = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d, 0x01, 0x02,
4142                   0x03, 0x04, 0x05, 0x06, 0x00 };
4143     unsigned int i;
4144     int tmp;
4145     u32 val;
4146 
4147     /* Initialise GPIO-connected stuff */
4148     gpio_inout(0xffffff, (1<<13));
4149     gpio_write(0);
4150     udelay(3);
4151     gpio_write(1<<13);
4152     /* GPIO inputs are pulled up, so no need to drive
4153      * reset pin any longer */
4154     gpio_bits(0xffffff, 0);
4155     if (bttv_gpio)
4156         bttv_gpio_tracking(btv,"pxc200");
4157 
4158     /*  we could/should try and reset/control the AD pots? but
4159         right now  we simply  turned off the crushing.  Without
4160         this the AGC drifts drifts
4161         remember the EN is reverse logic -->
4162         setting BT848_ADC_AGC_EN disable the AGC
4163         tboult@eecs.lehigh.edu
4164     */
4165 
4166     btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC);
4167 
4168     /*  Initialise MAX517 DAC */
4169     pr_info("Setting DAC reference voltage level ...\n");
4170     bttv_I2CWrite(btv,0x5E,0,0x80,1);
4171 
4172     /*  Initialise 12C508 PIC */
4173     /*  The I2CWrite and I2CRead commands are actually to the
4174      *  same chips - but the R/W bit is included in the address
4175      *  argument so the numbers are different */
4176 
4177 
4178     pr_info("Initialising 12C508 PIC chip ...\n");
4179 
4180     /* First of all, enable the clock line. This is used in the PXC200-F */
4181     val = btread(BT848_GPIO_DMA_CTL);
4182     val |= BT848_GPIO_DMA_CTL_GPCLKMODE;
4183     btwrite(val, BT848_GPIO_DMA_CTL);
4184 
4185     /* Then, push to 0 the reset pin long enough to reset the *
4186      * device same as above for the reset line, but not the same
4187      * value sent to the GPIO-connected stuff
4188      * which one is the good one? */
4189     gpio_inout(0xffffff,(1<<2));
4190     gpio_write(0);
4191     udelay(10);
4192     gpio_write(1<<2);
4193 
4194     for (i = 0; i < ARRAY_SIZE(vals); i++) {
4195         tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1);
4196         if (tmp != -1) {
4197             pr_info("I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n",
4198                    vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL));
4199         }
4200     }
4201 
4202     pr_info("PXC200 Initialised\n");
4203 }
4204 
4205 
4206 
4207 /* ----------------------------------------------------------------------- */
4208 /*
4209  *  The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock
4210  *  it. This apparently involves the following procedure for each 878 chip:
4211  *
4212  *  1) write 0x00C3FEFF to the GPIO_OUT_EN register
4213  *
4214  *  2)  write to GPIO_DATA
4215  *      - 0x0E
4216  *      - sleep 1ms
4217  *      - 0x10 + 0x0E
4218  *      - sleep 10ms
4219  *      - 0x0E
4220  *     read from GPIO_DATA into buf (uint_32)
4221  *      - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 )
4222  *                 error. ERROR_CPLD_Check_Failed stop.
4223  *
4224  *  3) write to GPIO_DATA
4225  *      - write 0x4400 + 0x0E
4226  *      - sleep 10ms
4227  *      - write 0x4410 + 0x0E
4228  *      - sleep 1ms
4229  *      - write 0x0E
4230  *     read from GPIO_DATA into buf (uint_32)
4231  *      - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 )
4232  *                error. ERROR_CPLD_Check_Failed.
4233  */
4234 /* ----------------------------------------------------------------------- */
4235 static void
4236 init_RTV24 (struct bttv *btv)
4237 {
4238     uint32_t dataRead = 0;
4239     long watchdog_value = 0x0E;
4240 
4241     pr_info("%d: Adlink RTV-24 initialisation in progress ...\n",
4242         btv->c.nr);
4243 
4244     btwrite (0x00c3feff, BT848_GPIO_OUT_EN);
4245 
4246     btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4247     msleep (1);
4248     btwrite (0x10 + watchdog_value, BT848_GPIO_DATA);
4249     msleep (10);
4250     btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4251 
4252     dataRead = btread (BT848_GPIO_DATA);
4253 
4254     if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) {
4255         pr_info("%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n",
4256             btv->c.nr, dataRead);
4257     }
4258 
4259     btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA);
4260     msleep (10);
4261     btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA);
4262     msleep (1);
4263     btwrite (watchdog_value, BT848_GPIO_DATA);
4264     msleep (1);
4265     dataRead = btread (BT848_GPIO_DATA);
4266 
4267     if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) {
4268         pr_info("%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n",
4269             btv->c.nr, dataRead);
4270 
4271         return;
4272     }
4273 
4274     pr_info("%d: Adlink RTV-24 initialisation complete\n", btv->c.nr);
4275 }
4276 
4277 
4278 
4279 /* ----------------------------------------------------------------------- */
4280 /*
4281  *  The PCI-8604PW contains a CPLD, probably an ispMACH 4A, that filters
4282  *  the PCI REQ signals coming from the four BT878 chips. After power
4283  *  up, the CPLD does not forward requests to the bus, which prevents
4284  *  the BT878 from fetching RISC instructions from memory. While the
4285  *  CPLD is connected to most of the GPIOs of PCI device 0xD, only
4286  *  five appear to play a role in unlocking the REQ signal. The following
4287  *  sequence has been determined by trial and error without access to the
4288  *  original driver.
4289  *
4290  *  Eight GPIOs of device 0xC are provided on connector CN4 (4 in, 4 out).
4291  *  Devices 0xE and 0xF do not appear to have anything connected to their
4292  *  GPIOs.
4293  *
4294  *  The correct GPIO_OUT_EN value might have some more bits set. It should
4295  *  be possible to derive it from a boundary scan of the CPLD. Its JTAG
4296  *  pins are routed to test points.
4297  *
4298  */
4299 /* ----------------------------------------------------------------------- */
4300 static void
4301 init_PCI8604PW(struct bttv *btv)
4302 {
4303     int state;
4304 
4305     if ((PCI_SLOT(btv->c.pci->devfn) & ~3) != 0xC) {
4306         pr_warn("This is not a PCI-8604PW\n");
4307         return;
4308     }
4309 
4310     if (PCI_SLOT(btv->c.pci->devfn) != 0xD)
4311         return;
4312 
4313     btwrite(0x080002, BT848_GPIO_OUT_EN);
4314 
4315     state = (btread(BT848_GPIO_DATA) >> 21) & 7;
4316 
4317     for (;;) {
4318         switch (state) {
4319         case 1:
4320         case 5:
4321         case 6:
4322         case 4:
4323             pr_debug("PCI-8604PW in state %i, toggling pin\n",
4324                  state);
4325             btwrite(0x080000, BT848_GPIO_DATA);
4326             msleep(1);
4327             btwrite(0x000000, BT848_GPIO_DATA);
4328             msleep(1);
4329             break;
4330         case 7:
4331             pr_info("PCI-8604PW unlocked\n");
4332             return;
4333         case 0:
4334             /* FIXME: If we are in state 7 and toggle GPIO[19] one
4335                more time, the CPLD goes into state 0, where PCI bus
4336                mastering is inhibited again. We have not managed to
4337                get out of that state. */
4338 
4339             pr_err("PCI-8604PW locked until reset\n");
4340             return;
4341         default:
4342             pr_err("PCI-8604PW in unknown state %i\n", state);
4343             return;
4344         }
4345 
4346         state = (state << 4) | ((btread(BT848_GPIO_DATA) >> 21) & 7);
4347 
4348         switch (state) {
4349         case 0x15:
4350         case 0x56:
4351         case 0x64:
4352         case 0x47:
4353         /* The transition from state 7 to state 0 is, as explained
4354            above, valid but undesired and with this code impossible
4355            as we exit as soon as we are in state 7.
4356         case 0x70: */
4357             break;
4358         default:
4359             pr_err("PCI-8604PW invalid transition %i -> %i\n",
4360                    state >> 4, state & 7);
4361             return;
4362         }
4363         state &= 7;
4364     }
4365 }
4366 
4367 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas]
4368  *
4369  * This is needed because rv605 don't use a normal multiplex, but a crosspoint
4370  * switch instead (CD22M3494E). This IC can have multiple active connections
4371  * between Xn (input) and Yn (output) pins. We need to clear any existing
4372  * connection prior to establish a new one, pulsing the STROBE pin.
4373  *
4374  * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
4375  * GPIO pins are wired as:
4376  *  GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
4377  *  GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
4378  *  GPIO[7]   - DATA (xpoint)    - P1[7] (microcontroller)
4379  *  GPIO[8]   -                  - P3[5] (microcontroller)
4380  *  GPIO[9]   - RESET (xpoint)   - P3[6] (microcontroller)
4381  *  GPIO[10]  - STROBE (xpoint)  - P3[7] (microcontroller)
4382  *  GPINTR    -                  - P3[4] (microcontroller)
4383  *
4384  * The microcontroller is a 80C32 like. It should be possible to change xpoint
4385  * configuration either directly (as we are doing) or using the microcontroller
4386  * which is also wired to I2C interface. I have no further info on the
4387  * microcontroller features, one would need to disassembly the firmware.
4388  * note: the vendor refused to give any information on this product, all
4389  *       that stuff was found using a multimeter! :)
4390  */
4391 static void rv605_muxsel(struct bttv *btv, unsigned int input)
4392 {
4393     static const u8 muxgpio[] = { 0x3, 0x1, 0x2, 0x4, 0xf, 0x7, 0xe, 0x0,
4394                       0xd, 0xb, 0xc, 0x6, 0x9, 0x5, 0x8, 0xa };
4395 
4396     gpio_bits(0x07f, muxgpio[input]);
4397 
4398     /* reset all connections */
4399     gpio_bits(0x200,0x200);
4400     mdelay(1);
4401     gpio_bits(0x200,0x000);
4402     mdelay(1);
4403 
4404     /* create a new connection */
4405     gpio_bits(0x480,0x480);
4406     mdelay(1);
4407     gpio_bits(0x480,0x080);
4408     mdelay(1);
4409 }
4410 
4411 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning]
4412  *
4413  * The CS16 (available on eBay cheap) is a PCI board with four Fusion
4414  * 878A chips, a PCI bridge, an Atmel microcontroller, four sync separator
4415  * chips, ten eight input analog multiplexors, a not chip and a few
4416  * other components.
4417  *
4418  * 16 inputs on a secondary bracket are provided and can be selected
4419  * from each of the four capture chips.  Two of the eight input
4420  * multiplexors are used to select from any of the 16 input signals.
4421  *
4422  * Unsupported hardware capabilities:
4423  *  . A video output monitor on the secondary bracket can be selected from
4424  *    one of the 878A chips.
4425  *  . Another passthrough but I haven't spent any time investigating it.
4426  *  . Digital I/O (logic level connected to GPIO) is available from an
4427  *    onboard header.
4428  *
4429  * The on chip input mux should always be set to 2.
4430  * GPIO[16:19] - Video input selection
4431  * GPIO[0:3]   - Video output monitor select (only available from one 878A)
4432  * GPIO[?:?]   - Digital I/O.
4433  *
4434  * There is an ATMEL microcontroller with an 8031 core on board.  I have not
4435  * determined what function (if any) it provides.  With the microcontroller
4436  * and sync separator chips a guess is that it might have to do with video
4437  * switching and maybe some digital I/O.
4438  */
4439 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input)
4440 {
4441     /* video mux */
4442     gpio_bits(0x0f0000, input << 16);
4443 }
4444 
4445 static void tibetCS16_init(struct bttv *btv)
4446 {
4447     /* enable gpio bits, mask obtained via btSpy */
4448     gpio_inout(0xffffff, 0x0f7fff);
4449     gpio_write(0x0f7fff);
4450 }
4451 
4452 /*
4453  * The following routines for the Kodicom-4400r get a little mind-twisting.
4454  * There is a "master" controller and three "slave" controllers, together
4455  * an analog switch which connects any of 16 cameras to any of the BT87A's.
4456  * The analog switch is controlled by the "master", but the detection order
4457  * of the four BT878A chips is in an order which I just don't understand.
4458  * The "master" is actually the second controller to be detected.  The
4459  * logic on the board uses logical numbers for the 4 controllers, but
4460  * those numbers are different from the detection sequence.  When working
4461  * with the analog switch, we need to "map" from the detection sequence
4462  * over to the board's logical controller number.  This mapping sequence
4463  * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
4464  * unit 3, the second (which is the master) is logical unit 0, etc.
4465  * We need to maintain the status of the analog switch (which of the 16
4466  * cameras is connected to which of the 4 controllers) in sw_status array.
4467  */
4468 
4469 /*
4470  * First a routine to set the analog switch, which controls which camera
4471  * is routed to which controller.  The switch comprises an X-address
4472  * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4473  * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4474  * A data value (gpio bit 7) of '1' enables the switch, and '0' disables
4475  * the switch.  A STROBE bit (gpio bit 8) latches the data value into the
4476  * specified address.  The idea is to set the address and data, then bring
4477  * STROBE high, and finally bring STROBE back to low.
4478  */
4479 static void kodicom4400r_write(struct bttv *btv,
4480                    unsigned char xaddr,
4481                    unsigned char yaddr,
4482                    unsigned char data) {
4483     unsigned int udata;
4484 
4485     udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf);
4486     gpio_bits(0x1ff, udata);        /* write ADDR and DAT */
4487     gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */
4488     gpio_bits(0x1ff, udata);        /* strobe low */
4489 }
4490 
4491 /*
4492  * Next the mux select.  Both the "master" and "slave" 'cards' (controllers)
4493  * use this routine.  The routine finds the "master" for the card, maps
4494  * the controller number from the detected position over to the logical
4495  * number, writes the appropriate data to the analog switch, and housekeeps
4496  * the local copy of the switch information.  The parameter 'input' is the
4497  * requested camera number (0 - 15).
4498  */
4499 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
4500 {
4501     int xaddr, yaddr;
4502     struct bttv *mctlr;
4503     static unsigned char map[4] = {3, 0, 2, 1};
4504 
4505     mctlr = master[btv->c.nr];
4506     if (mctlr == NULL) {    /* ignore if master not yet detected */
4507         return;
4508     }
4509     yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
4510     yaddr = map[yaddr];
4511     xaddr = input & 0xf;
4512     /* Check if the controller/camera pair has changed, else ignore */
4513     if (mctlr->sw_status[yaddr] != xaddr)
4514     {
4515         /* "open" the old switch, "close" the new one, save the new */
4516         kodicom4400r_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
4517         mctlr->sw_status[yaddr] = xaddr;
4518         kodicom4400r_write(mctlr, xaddr, yaddr, 1);
4519     }
4520 }
4521 
4522 /*
4523  * During initialisation, we need to reset the analog switch.  We
4524  * also preset the switch to map the 4 connectors on the card to the
4525  * *user's* (see above description of kodicom4400r_muxsel) channels
4526  * 0 through 3
4527  */
4528 static void kodicom4400r_init(struct bttv *btv)
4529 {
4530     int ix;
4531 
4532     gpio_inout(0x0003ff, 0x0003ff);
4533     gpio_write(1 << 9); /* reset MUX */
4534     gpio_write(0);
4535     /* Preset camera 0 to the 4 controllers */
4536     for (ix = 0; ix < 4; ix++) {
4537         btv->sw_status[ix] = ix;
4538         kodicom4400r_write(btv, ix, ix, 1);
4539     }
4540     /*
4541      * Since this is the "master", we need to set up the
4542      * other three controller chips' pointers to this structure
4543      * for later use in the muxsel routine.
4544      */
4545     if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3))
4546         return;
4547     master[btv->c.nr-1] = btv;
4548     master[btv->c.nr]   = btv;
4549     master[btv->c.nr+1] = btv;
4550     master[btv->c.nr+2] = btv;
4551 }
4552 
4553 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel
4554  * video multiplexers to provide up to 16 video inputs. These
4555  * multiplexers are controlled by the lower 8 GPIO pins of the
4556  * bt878. The multiplexers probably Pericom PI5V331Q or similar.
4557 
4558  * xxx0 is pin xxx of multiplexer U5,
4559  * yyy1 is pin yyy of multiplexer U2
4560  */
4561 #define ENA0    0x01
4562 #define ENB0    0x02
4563 #define ENA1    0x04
4564 #define ENB1    0x08
4565 
4566 #define IN10    0x10
4567 #define IN00    0x20
4568 #define IN11    0x40
4569 #define IN01    0x80
4570 
4571 static void xguard_muxsel(struct bttv *btv, unsigned int input)
4572 {
4573     static const int masks[] = {
4574         ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10,
4575         ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10,
4576         ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11,
4577         ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11,
4578     };
4579     gpio_write(masks[input%16]);
4580 }
4581 static void picolo_tetra_init(struct bttv *btv)
4582 {
4583     /*This is the video input redirection functionality : I DID NOT USE IT. */
4584     btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */
4585     btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A]  set to 1*/
4586 }
4587 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input)
4588 {
4589 
4590     dprintk("%d : picolo_tetra_muxsel =>  input = %d\n", btv->c.nr, input);
4591     /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/
4592     /*GPIO[20]&GPIO[21] used to choose the right input*/
4593     btwrite (input<<20,BT848_GPIO_DATA);
4594 
4595 }
4596 
4597 /*
4598  * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>]
4599  *
4600  * The IVC120G security card has 4 i2c controlled TDA8540 matrix
4601  * switchers to provide 16 channels to MUX0. The TDA8540's have
4602  * 4 independent outputs and as such the IVC120G also has the
4603  * optional "Monitor Out" bus. This allows the card to be looking
4604  * at one input while the monitor is looking at another.
4605  *
4606  * Since I've couldn't be bothered figuring out how to add an
4607  * independent muxsel for the monitor bus, I've just set it to
4608  * whatever the card is looking at.
4609  *
4610  *  OUT0 of the TDA8540's is connected to MUX0         (0x03)
4611  *  OUT1 of the TDA8540's is connected to "Monitor Out"        (0x0C)
4612  *
4613  *  TDA8540_ALT3 IN0-3 = Channel 13 - 16       (0x03)
4614  *  TDA8540_ALT4 IN0-3 = Channel 1 - 4         (0x03)
4615  *  TDA8540_ALT5 IN0-3 = Channel 5 - 8         (0x03)
4616  *  TDA8540_ALT6 IN0-3 = Channel 9 - 12                (0x03)
4617  *
4618  */
4619 
4620 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */
4621 #define I2C_TDA8540        0x90
4622 #define I2C_TDA8540_ALT1   0x92
4623 #define I2C_TDA8540_ALT2   0x94
4624 #define I2C_TDA8540_ALT3   0x96
4625 #define I2C_TDA8540_ALT4   0x98
4626 #define I2C_TDA8540_ALT5   0x9a
4627 #define I2C_TDA8540_ALT6   0x9c
4628 
4629 static void ivc120_muxsel(struct bttv *btv, unsigned int input)
4630 {
4631     /* Simple maths */
4632     int key = input % 4;
4633     int matrix = input / 4;
4634 
4635     dprintk("%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n",
4636         btv->c.nr, input, matrix, key);
4637 
4638     /* Handles the input selection on the TDA8540's */
4639     bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00,
4640               ((matrix == 3) ? (key | key << 2) : 0x00), 1);
4641     bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00,
4642               ((matrix == 0) ? (key | key << 2) : 0x00), 1);
4643     bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00,
4644               ((matrix == 1) ? (key | key << 2) : 0x00), 1);
4645     bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00,
4646               ((matrix == 2) ? (key | key << 2) : 0x00), 1);
4647 
4648     /* Handles the output enables on the TDA8540's */
4649     bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02,
4650               ((matrix == 3) ? 0x03 : 0x00), 1);  /* 13 - 16 */
4651     bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02,
4652               ((matrix == 0) ? 0x03 : 0x00), 1);  /* 1-4 */
4653     bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02,
4654               ((matrix == 1) ? 0x03 : 0x00), 1);  /* 5-8 */
4655     bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02,
4656               ((matrix == 2) ? 0x03 : 0x00), 1);  /* 9-12 */
4657 
4658     /* 878's MUX0 is already selected for input via muxsel values */
4659 }
4660 
4661 
4662 /* PXC200 muxsel helper
4663  * luke@syseng.anu.edu.au
4664  * another transplant
4665  * from Alessandro Rubini (rubini@linux.it)
4666  *
4667  * There are 4 kinds of cards:
4668  * PXC200L which is bt848
4669  * PXC200F which is bt848 with PIC controlling mux
4670  * PXC200AL which is bt878
4671  * PXC200AF which is bt878 with PIC controlling mux
4672  */
4673 #define PX_CFG_PXC200F 0x01
4674 #define PX_FLAG_PXC200A  0x00001000 /* a pxc200A is bt-878 based */
4675 #define PX_I2C_PIC       0x0f
4676 #define PX_PXC200A_CARDID 0x200a1295
4677 #define PX_I2C_CMD_CFG   0x00
4678 
4679 static void PXC200_muxsel(struct bttv *btv, unsigned int input)
4680 {
4681     int rc;
4682     long mux;
4683     int bitmask;
4684     unsigned char buf[2];
4685 
4686     /* Read PIC config to determine if this is a PXC200F */
4687     /* PX_I2C_CMD_CFG*/
4688     buf[0]=0;
4689     buf[1]=0;
4690     rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1);
4691     if (rc) {
4692         pr_debug("%d: PXC200_muxsel: pic cfg write failed:%d\n",
4693              btv->c.nr, rc);
4694       /* not PXC ? do nothing */
4695         return;
4696     }
4697 
4698     rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL);
4699     if (!(rc & PX_CFG_PXC200F)) {
4700         pr_debug("%d: PXC200_muxsel: not PXC200F rc:%d\n",
4701              btv->c.nr, rc);
4702         return;
4703     }
4704 
4705 
4706     /* The multiplexer in the 200F is handled by the GPIO port */
4707     /* get correct mapping between inputs  */
4708     /*  mux = bttv_tvcards[btv->type].muxsel[input] & 3; */
4709     /* ** not needed!?   */
4710     mux = input;
4711 
4712     /* make sure output pins are enabled */
4713     /* bitmask=0x30f; */
4714     bitmask=0x302;
4715     /* check whether we have a PXC200A */
4716     if (btv->cardid == PX_PXC200A_CARDID)  {
4717        bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */
4718        bitmask |= 7<<4; /* the DAC */
4719     }
4720     btwrite(bitmask, BT848_GPIO_OUT_EN);
4721 
4722     bitmask = btread(BT848_GPIO_DATA);
4723     if (btv->cardid == PX_PXC200A_CARDID)
4724       bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7);
4725     else /* older device */
4726       bitmask = (bitmask & ~0x300) | ((mux & 3) << 8);
4727     btwrite(bitmask,BT848_GPIO_DATA);
4728 
4729     /*
4730      * Was "to be safe, set the bt848 to input 0"
4731      * Actually, since it's ok at load time, better not messing
4732      * with these bits (on PXC200AF you need to set mux 2 here)
4733      *
4734      * needed because bttv-driver sets mux before calling this function
4735      */
4736     if (btv->cardid == PX_PXC200A_CARDID)
4737       btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM);
4738     else /* older device */
4739       btand(~BT848_IFORM_MUXSEL,BT848_IFORM);
4740 
4741     pr_debug("%d: setting input channel to:%d\n", btv->c.nr, (int)mux);
4742 }
4743 
4744 static void phytec_muxsel(struct bttv *btv, unsigned int input)
4745 {
4746     unsigned int mux = input % 4;
4747 
4748     if (input == btv->svhs)
4749         mux = 0;
4750 
4751     gpio_bits(0x3, mux);
4752 }
4753 
4754 /*
4755  * GeoVision GV-800(S) functions
4756  * Bruno Christo <bchristo@inf.ufsm.br>
4757 */
4758 
4759 /* This is a function to control the analog switch, which determines which
4760  * camera is routed to which controller.  The switch comprises an X-address
4761  * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4762  * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4763  * A data value (gpio bit 18) of '1' enables the switch, and '0' disables
4764  * the switch.  A STROBE bit (gpio bit 17) latches the data value into the
4765  * specified address. There is also a chip select (gpio bit 16).
4766  * The idea is to set the address and chip select together, bring
4767  * STROBE high, write the data, and finally bring STROBE back to low.
4768  */
4769 static void gv800s_write(struct bttv *btv,
4770              unsigned char xaddr,
4771              unsigned char yaddr,
4772              unsigned char data) {
4773     /* On the "master" 878A:
4774     * GPIO bits 0-9 are used for the analog switch:
4775     *   00 - 03:    camera selector
4776     *   04 - 06:    878A (controller) selector
4777     *   16:     cselect
4778     *   17:     strobe
4779     *   18:     data (1->on, 0->off)
4780     *   19:     reset
4781     */
4782     const u32 ADDRESS = ((xaddr&0xf) | (yaddr&3)<<4);
4783     const u32 CSELECT = 1<<16;
4784     const u32 STROBE = 1<<17;
4785     const u32 DATA = data<<18;
4786 
4787     gpio_bits(0x1007f, ADDRESS | CSELECT);  /* write ADDRESS and CSELECT */
4788     gpio_bits(0x20000, STROBE);     /* STROBE high */
4789     gpio_bits(0x40000, DATA);       /* write DATA */
4790     gpio_bits(0x20000, ~STROBE);        /* STROBE low */
4791 }
4792 
4793 /*
4794  * GeoVision GV-800(S) muxsel
4795  *
4796  * Each of the 4 cards (controllers) use this function.
4797  * The controller using this function selects the input through the GPIO pins
4798  * of the "master" card. A pointer to this card is stored in master[btv->c.nr].
4799  *
4800  * The parameter 'input' is the requested camera number (0-4) on the controller.
4801  * The map array has the address of each input. Note that the addresses in the
4802  * array are in the sequence the original GeoVision driver uses, that is, set
4803  * every controller to input 0, then to input 1, 2, 3, repeat. This means that
4804  * the physical "camera 1" connector corresponds to controller 0 input 0,
4805  * "camera 2" corresponds to controller 1 input 0, and so on.
4806  *
4807  * After getting the input address, the function then writes the appropriate
4808  * data to the analog switch, and housekeeps the local copy of the switch
4809  * information.
4810  */
4811 static void gv800s_muxsel(struct bttv *btv, unsigned int input)
4812 {
4813     struct bttv *mctlr;
4814     int xaddr, yaddr;
4815     static unsigned int map[4][4] = { { 0x0, 0x4, 0xa, 0x6 },
4816                       { 0x1, 0x5, 0xb, 0x7 },
4817                       { 0x2, 0x8, 0xc, 0xe },
4818                       { 0x3, 0x9, 0xd, 0xf } };
4819     input = input%4;
4820     mctlr = master[btv->c.nr];
4821     if (mctlr == NULL) {
4822         /* do nothing until the "master" is detected */
4823         return;
4824     }
4825     yaddr = (btv->c.nr - mctlr->c.nr) & 3;
4826     xaddr = map[yaddr][input] & 0xf;
4827 
4828     /* Check if the controller/camera pair has changed, ignore otherwise */
4829     if (mctlr->sw_status[yaddr] != xaddr) {
4830         /* disable the old switch, enable the new one and save status */
4831         gv800s_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
4832         mctlr->sw_status[yaddr] = xaddr;
4833         gv800s_write(mctlr, xaddr, yaddr, 1);
4834     }
4835 }
4836 
4837 /* GeoVision GV-800(S) "master" chip init */
4838 static void gv800s_init(struct bttv *btv)
4839 {
4840     int ix;
4841 
4842     gpio_inout(0xf107f, 0xf107f);
4843     gpio_write(1<<19); /* reset the analog MUX */
4844     gpio_write(0);
4845 
4846     /* Preset camera 0 to the 4 controllers */
4847     for (ix = 0; ix < 4; ix++) {
4848         btv->sw_status[ix] = ix;
4849         gv800s_write(btv, ix, ix, 1);
4850     }
4851 
4852     /* Inputs on the "master" controller need this brightness fix */
4853     bttv_I2CWrite(btv, 0x18, 0x5, 0x90, 1);
4854 
4855     if (btv->c.nr > BTTV_MAX-4)
4856         return;
4857     /*
4858      * Store the "master" controller pointer in the master
4859      * array for later use in the muxsel function.
4860      */
4861     master[btv->c.nr]   = btv;
4862     master[btv->c.nr+1] = btv;
4863     master[btv->c.nr+2] = btv;
4864     master[btv->c.nr+3] = btv;
4865 }
4866 
4867 /* ----------------------------------------------------------------------- */
4868 /* motherboard chipset specific stuff                                      */
4869 
4870 void __init bttv_check_chipset(void)
4871 {
4872     int pcipci_fail = 0;
4873     struct pci_dev *dev = NULL;
4874 
4875     if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL))   /* should check if target is AGP */
4876         pcipci_fail = 1;
4877     if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF))
4878         triton1 = 1;
4879     if (pci_pci_problems & PCIPCI_VSFX)
4880         vsfx = 1;
4881 #ifdef PCIPCI_ALIMAGIK
4882     if (pci_pci_problems & PCIPCI_ALIMAGIK)
4883         latency = 0x0A;
4884 #endif
4885 
4886 
4887     /* print warnings about any quirks found */
4888     if (triton1)
4889         pr_info("Host bridge needs ETBF enabled\n");
4890     if (vsfx)
4891         pr_info("Host bridge needs VSFX enabled\n");
4892     if (pcipci_fail) {
4893         pr_info("bttv and your chipset may not work together\n");
4894         if (!no_overlay) {
4895             pr_info("overlay will be disabled\n");
4896             no_overlay = 1;
4897         } else {
4898             pr_info("overlay forced. Use this option at your own risk.\n");
4899         }
4900     }
4901     if (UNSET != latency)
4902         pr_info("pci latency fixup [%d]\n", latency);
4903     while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL,
4904                       PCI_DEVICE_ID_INTEL_82441, dev))) {
4905         unsigned char b;
4906         pci_read_config_byte(dev, 0x53, &b);
4907         if (bttv_debug)
4908             pr_info("Host bridge: 82441FX Natoma, bufcon=0x%02x\n",
4909                 b);
4910     }
4911 }
4912 
4913 int bttv_handle_chipset(struct bttv *btv)
4914 {
4915     unsigned char command;
4916 
4917     if (!triton1 && !vsfx && UNSET == latency)
4918         return 0;
4919 
4920     if (bttv_verbose) {
4921         if (triton1)
4922             pr_info("%d: enabling ETBF (430FX/VP3 compatibility)\n",
4923                 btv->c.nr);
4924         if (vsfx && btv->id >= 878)
4925             pr_info("%d: enabling VSFX\n", btv->c.nr);
4926         if (UNSET != latency)
4927             pr_info("%d: setting pci timer to %d\n",
4928                 btv->c.nr, latency);
4929     }
4930 
4931     if (btv->id < 878) {
4932         /* bt848 (mis)uses a bit in the irq mask for etbf */
4933         if (triton1)
4934             btv->triton1 = BT848_INT_ETBF;
4935     } else {
4936         /* bt878 has a bit in the pci config space for it */
4937         pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command);
4938         if (triton1)
4939             command |= BT878_EN_TBFX;
4940         if (vsfx)
4941             command |= BT878_EN_VSFX;
4942         pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command);
4943     }
4944     if (UNSET != latency)
4945         pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency);
4946     return 0;
4947 }
[ Source navigation ] [ Diff markup ] [ Identifier search ] [ general search ]

This page was automatically generated by the 2.1.0 LXR engine.

The LXR team
Valid CSS 2.1! Valid HTML 4.01!