0001 // SPDX-License-Identifier: GPL-2.0
0002 /*
0003 * Support for CompuLab CM-T54
0004 */
0005 /dts-v1/;
0006
0007 #include "omap5.dtsi"
0008 #include <dt-bindings/interrupt-controller/irq.h>
0009 #include <dt-bindings/interrupt-controller/arm-gic.h>
0010
0011 / {
0012 model = "CompuLab CM-T54";
0013 compatible = "compulab,omap5-cm-t54", "ti,omap5";
0014
0015 memory@80000000 {
0016 device_type = "memory";
0017 reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
0018 };
0019
0020 aliases {
0021 display0 = &hdmi0;
0022 display1 = &dvi0;
0023 display2 = &lcd0;
0024 };
0025
0026 vmmcsd_fixed: fixed-regulator-mmcsd {
0027 compatible = "regulator-fixed";
0028 regulator-name = "vmmcsd_fixed";
0029 regulator-min-microvolt = <3300000>;
0030 regulator-max-microvolt = <3300000>;
0031 };
0032
0033 vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
0034 compatible = "regulator-fixed";
0035 regulator-name = "vwlan_pdn_fixed";
0036 regulator-min-microvolt = <3300000>;
0037 regulator-max-microvolt = <3300000>;
0038 vin-supply = <&ldo2_reg>;
0039 gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* gpio4_109 */
0040 startup-delay-us = <1000>;
0041 enable-active-high;
0042 };
0043
0044 vwlan_fixed: fixed-regulator-vwlan {
0045 compatible = "regulator-fixed";
0046 regulator-name = "vwlan_fixed";
0047 regulator-min-microvolt = <3300000>;
0048 regulator-max-microvolt = <3300000>;
0049 vin-supply = <&vwlan_pdn_fixed>;
0050 gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio4_110 */
0051 startup-delay-us = <1000>;
0052 enable-active-high;
0053 };
0054
0055 ads7846reg: ads7846-reg {
0056 compatible = "regulator-fixed";
0057 regulator-name = "ads7846-reg";
0058 regulator-min-microvolt = <3300000>;
0059 regulator-max-microvolt = <3300000>;
0060 };
0061
0062 /* HS USB Host PHY on PORT 2 */
0063 hsusb2_phy: hsusb2_phy {
0064 compatible = "usb-nop-xceiv";
0065 reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
0066 #phy-cells = <0>;
0067 };
0068
0069 /* HS USB Host PHY on PORT 3 */
0070 hsusb3_phy: hsusb3_phy {
0071 compatible = "usb-nop-xceiv";
0072 reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
0073 #phy-cells = <0>;
0074 };
0075
0076 leds {
0077 compatible = "gpio-leds";
0078 led1 {
0079 label = "Heartbeat";
0080 gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
0081 linux,default-trigger = "heartbeat";
0082 default-state = "off";
0083 };
0084 };
0085
0086 lcd0: display {
0087 compatible = "startek,startek-kd050c", "panel-dpi";
0088 label = "lcd";
0089
0090 pinctrl-names = "default";
0091 pinctrl-0 = <&lcd_pins>;
0092
0093 enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
0094
0095 panel-timing {
0096 clock-frequency = <33000000>;
0097 hactive = <800>;
0098 vactive = <480>;
0099 hfront-porch = <40>;
0100 hback-porch = <40>;
0101 hsync-len = <43>;
0102 vback-porch = <29>;
0103 vfront-porch = <13>;
0104 vsync-len = <3>;
0105 hsync-active = <0>;
0106 vsync-active = <0>;
0107 de-active = <1>;
0108 pixelclk-active = <1>;
0109 };
0110
0111 port {
0112 lcd_in: endpoint {
0113 remote-endpoint = <&dpi_lcd_out>;
0114 };
0115 };
0116 };
0117
0118 hdmi0: connector0 {
0119 compatible = "hdmi-connector";
0120 label = "hdmi";
0121
0122 type = "a";
0123
0124 pinctrl-names = "default";
0125 pinctrl-0 = <&hdmi_conn_pins>;
0126
0127 hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
0128
0129 port {
0130 hdmi_connector_in: endpoint {
0131 remote-endpoint = <&hdmi_out>;
0132 };
0133 };
0134 };
0135
0136 tfp410: encoder0 {
0137 compatible = "ti,tfp410";
0138
0139 ports {
0140 #address-cells = <1>;
0141 #size-cells = <0>;
0142
0143 port@0 {
0144 reg = <0>;
0145
0146 tfp410_in: endpoint {
0147 remote-endpoint = <&dpi_dvi_out>;
0148 };
0149 };
0150
0151 port@1 {
0152 reg = <1>;
0153
0154 tfp410_out: endpoint {
0155 remote-endpoint = <&dvi_connector_in>;
0156 };
0157 };
0158 };
0159 };
0160
0161 dvi0: connector1 {
0162 compatible = "dvi-connector";
0163 label = "dvi";
0164
0165 digital;
0166
0167 ddc-i2c-bus = <&i2c2>;
0168
0169 port {
0170 dvi_connector_in: endpoint {
0171 remote-endpoint = <&tfp410_out>;
0172 };
0173 };
0174 };
0175 };
0176
0177 &omap5_pmx_wkup {
0178
0179 ads7846_pins: pinmux_ads7846_pins {
0180 pinctrl-single,pins = <
0181 OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */
0182 >;
0183 };
0184
0185 palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
0186 pinctrl-single,pins = <
0187 /* sys_nirq1 is pulled down as the SoC is inverting it for GIC */
0188 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0)
0189 >;
0190 };
0191 };
0192
0193 &omap5_pmx_core {
0194 pinctrl-names = "default";
0195 pinctrl-0 = <
0196 &led_gpio_pins
0197 &usbhost_pins
0198 >;
0199
0200 led_gpio_pins: pinmux_led_gpio_pins {
0201 pinctrl-single,pins = <
0202 OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
0203 >;
0204 };
0205
0206 i2c1_pins: pinmux_i2c1_pins {
0207 pinctrl-single,pins = <
0208 OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
0209 OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
0210 >;
0211 };
0212
0213 i2c2_pins: pinmux_i2c2_pins {
0214 pinctrl-single,pins = <
0215 OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
0216 OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
0217 >;
0218 };
0219
0220 mmc1_pins: pinmux_mmc1_pins {
0221 pinctrl-single,pins = <
0222 OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
0223 OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
0224 OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
0225 OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
0226 OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
0227 OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
0228 >;
0229 };
0230
0231 mmc2_pins: pinmux_mmc2_pins {
0232 pinctrl-single,pins = <
0233 OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
0234 OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
0235 OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
0236 OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
0237 OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
0238 OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
0239 OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
0240 OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
0241 OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
0242 OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
0243 >;
0244 };
0245
0246 mmc3_pins: pinmux_mmc3_pins {
0247 pinctrl-single,pins = <
0248 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
0249 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
0250 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
0251 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
0252 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
0253 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
0254 >;
0255 };
0256
0257 wlan_gpios_pins: pinmux_wlan_gpios_pins {
0258 pinctrl-single,pins = <
0259 OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
0260 OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
0261 >;
0262 };
0263
0264 usbhost_pins: pinmux_usbhost_pins {
0265 pinctrl-single,pins = <
0266 OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
0267 OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
0268
0269 OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
0270 OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
0271
0272 OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
0273 OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
0274 >;
0275 };
0276
0277 dss_hdmi_pins: pinmux_dss_hdmi_pins {
0278 pinctrl-single,pins = <
0279 OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
0280 OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
0281 OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
0282 >;
0283 };
0284
0285 lcd_pins: pinmux_lcd_pins {
0286 pinctrl-single,pins = <
0287 OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
0288 >;
0289 };
0290
0291 hdmi_conn_pins: pinmux_hdmi_conn_pins {
0292 pinctrl-single,pins = <
0293 OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
0294 >;
0295 };
0296
0297 dss_dpi_pins: pinmux_dss_dpi_pins {
0298 pinctrl-single,pins = <
0299 OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
0300 OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
0301 OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
0302 OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
0303 OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
0304 OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
0305 OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
0306 OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
0307 OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
0308 OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
0309 OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
0310 OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
0311 OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
0312 OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
0313 OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
0314 OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
0315 OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
0316 OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
0317 OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
0318 OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
0319 OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
0320 OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
0321 OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
0322 OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
0323 OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
0324 OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
0325 OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
0326 OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
0327 >;
0328 };
0329
0330 mcspi2_pins: pinmux_mcspi1_pins {
0331 pinctrl-single,pins = <
0332 OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
0333 OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
0334 OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
0335 OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
0336 >;
0337 };
0338 };
0339
0340 &mcspi2 {
0341 pinctrl-names = "default";
0342 pinctrl-0 = <&mcspi2_pins>;
0343
0344 /* touch controller */
0345 ads7846@0 {
0346 pinctrl-names = "default";
0347 pinctrl-0 = <&ads7846_pins>;
0348
0349 compatible = "ti,ads7846";
0350 vcc-supply = <&ads7846reg>;
0351
0352 reg = <0>; /* CS0 */
0353 spi-max-frequency = <1500000>;
0354
0355 interrupt-parent = <&gpio1>;
0356 interrupts = <15 0>; /* gpio1_wk15 */
0357 pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
0358
0359
0360 ti,x-min = /bits/ 16 <0x0>;
0361 ti,x-max = /bits/ 16 <0x0fff>;
0362 ti,y-min = /bits/ 16 <0x0>;
0363 ti,y-max = /bits/ 16 <0x0fff>;
0364
0365 ti,x-plate-ohms = /bits/ 16 <180>;
0366 ti,pressure-max = /bits/ 16 <255>;
0367
0368 ti,debounce-max = /bits/ 16 <30>;
0369 ti,debounce-tol = /bits/ 16 <10>;
0370 ti,debounce-rep = /bits/ 16 <1>;
0371
0372 wakeup-source;
0373 };
0374 };
0375
0376 &mmc1 {
0377 pinctrl-names = "default";
0378 pinctrl-0 = <&mmc1_pins>;
0379 vmmc-supply = <&ldo9_reg>;
0380 bus-width = <4>;
0381 };
0382
0383 &mmc2 {
0384 pinctrl-names = "default";
0385 pinctrl-0 = <&mmc2_pins>;
0386 vmmc-supply = <&vmmcsd_fixed>;
0387 bus-width = <8>;
0388 ti,non-removable;
0389 };
0390
0391 &mmc3 {
0392 pinctrl-names = "default";
0393 pinctrl-0 = <
0394 &mmc3_pins
0395 &wlan_gpios_pins
0396 >;
0397 vmmc-supply = <&vwlan_fixed>;
0398 bus-width = <4>;
0399 ti,non-removable;
0400 };
0401
0402 &mmc4 {
0403 status = "disabled";
0404 };
0405
0406 &mmc5 {
0407 status = "disabled";
0408 };
0409
0410 &i2c1 {
0411 pinctrl-names = "default";
0412 pinctrl-0 = <&i2c1_pins>;
0413
0414 clock-frequency = <400000>;
0415
0416 at24@50 {
0417 compatible = "atmel,24c02";
0418 pagesize = <16>;
0419 reg = <0x50>;
0420 };
0421
0422 palmas: palmas@48 {
0423 compatible = "ti,palmas";
0424 reg = <0x48>;
0425 pinctrl-0 = <&palmas_sys_nirq_pins>;
0426 pinctrl-names = "default";
0427 /* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */
0428 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_LOW>;
0429 interrupt-controller;
0430 #interrupt-cells = <2>;
0431 ti,system-power-controller;
0432
0433 extcon_usb3: palmas_usb {
0434 compatible = "ti,palmas-usb-vid";
0435 ti,enable-vbus-detection;
0436 ti,enable-id-detection;
0437 ti,wakeup;
0438 };
0439
0440 rtc {
0441 compatible = "ti,palmas-rtc";
0442 interrupt-parent = <&palmas>;
0443 interrupts = <8 IRQ_TYPE_NONE>;
0444 };
0445
0446 palmas_pmic {
0447 compatible = "ti,palmas-pmic";
0448 interrupt-parent = <&palmas>;
0449 interrupts = <14 IRQ_TYPE_NONE>;
0450 interrupt-names = "short-irq";
0451
0452 ti,ldo6-vibrator;
0453
0454 regulators {
0455 smps123_reg: smps123 {
0456 /* VDD_OPP_MPU */
0457 regulator-name = "smps123";
0458 regulator-min-microvolt = < 600000>;
0459 regulator-max-microvolt = <1500000>;
0460 regulator-always-on;
0461 regulator-boot-on;
0462 };
0463
0464 smps45_reg: smps45 {
0465 /* VDD_OPP_MM */
0466 regulator-name = "smps45";
0467 regulator-min-microvolt = < 600000>;
0468 regulator-max-microvolt = <1310000>;
0469 regulator-always-on;
0470 regulator-boot-on;
0471 };
0472
0473 smps6_reg: smps6 {
0474 /* VDD_DDR3 - over VDD_SMPS6 */
0475 regulator-name = "smps6";
0476 regulator-min-microvolt = <1500000>;
0477 regulator-max-microvolt = <1500000>;
0478 regulator-always-on;
0479 regulator-boot-on;
0480 };
0481
0482 smps7_reg: smps7 {
0483 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
0484 regulator-name = "smps7";
0485 regulator-min-microvolt = <1800000>;
0486 regulator-max-microvolt = <1800000>;
0487 regulator-always-on;
0488 regulator-boot-on;
0489 };
0490
0491 smps8_reg: smps8 {
0492 /* VDD_OPP_CORE */
0493 regulator-name = "smps8";
0494 regulator-min-microvolt = < 600000>;
0495 regulator-max-microvolt = <1310000>;
0496 regulator-always-on;
0497 regulator-boot-on;
0498 };
0499
0500 smps9_reg: smps9 {
0501 /* VDDA_2v1_AUD over VDD_2v1 */
0502 regulator-name = "smps9";
0503 regulator-min-microvolt = <3300000>;
0504 regulator-max-microvolt = <3300000>;
0505 ti,smps-range = <0x80>;
0506 regulator-always-on;
0507 regulator-boot-on;
0508 };
0509
0510 smps10_out2_reg: smps10_out2 {
0511 /* VBUS_5V_OTG */
0512 regulator-name = "smps10_out2";
0513 regulator-min-microvolt = <5000000>;
0514 regulator-max-microvolt = <5000000>;
0515 regulator-always-on;
0516 regulator-boot-on;
0517 };
0518
0519 smps10_out1_reg: smps10_out1 {
0520 /* VBUS_5V_OTG */
0521 regulator-name = "smps10_out1";
0522 regulator-min-microvolt = <5000000>;
0523 regulator-max-microvolt = <5000000>;
0524 };
0525
0526 ldo1_reg: ldo1 {
0527 /* VDDAPHY_CAM: vdda_csiport */
0528 regulator-name = "ldo1";
0529 regulator-min-microvolt = <1800000>;
0530 regulator-max-microvolt = <1800000>;
0531 };
0532
0533 ldo2_reg: ldo2 {
0534 /* VDD_3V3_WLAN */
0535 regulator-name = "ldo2";
0536 regulator-min-microvolt = <3300000>;
0537 regulator-max-microvolt = <3300000>;
0538 startup-delay-us = <1000>;
0539 };
0540
0541 ldo3_reg: ldo3 {
0542 /* VCC_1V5_AUD */
0543 regulator-name = "ldo3";
0544 regulator-min-microvolt = <1500000>;
0545 regulator-max-microvolt = <1500000>;
0546 regulator-always-on;
0547 regulator-boot-on;
0548 };
0549
0550 ldo4_reg: ldo4 {
0551 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
0552 regulator-name = "ldo4";
0553 regulator-min-microvolt = <1800000>;
0554 regulator-max-microvolt = <1800000>;
0555 };
0556
0557 ldo5_reg: ldo5 {
0558 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
0559 regulator-name = "ldo5";
0560 regulator-min-microvolt = <1800000>;
0561 regulator-max-microvolt = <1800000>;
0562 regulator-always-on;
0563 regulator-boot-on;
0564 };
0565
0566 ldo6_reg: ldo6 {
0567 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
0568 regulator-name = "ldo6";
0569 regulator-min-microvolt = <1200000>;
0570 regulator-max-microvolt = <1200000>;
0571 regulator-always-on;
0572 regulator-boot-on;
0573 };
0574
0575 ldo7_reg: ldo7 {
0576 /* VDD_VPP: vpp1 */
0577 regulator-name = "ldo7";
0578 regulator-min-microvolt = <2000000>;
0579 regulator-max-microvolt = <2000000>;
0580 /* Only for efuse reprograming! */
0581 status = "disabled";
0582 };
0583
0584 ldo8_reg: ldo8 {
0585 /* VDD_3V_GP: act led/serial console */
0586 regulator-name = "ldo8";
0587 regulator-min-microvolt = <3000000>;
0588 regulator-max-microvolt = <3000000>;
0589 regulator-always-on;
0590 regulator-boot-on;
0591 };
0592
0593 ldo9_reg: ldo9 {
0594 /* VCC_DV_SDIO: vdds_sdcard */
0595 regulator-name = "ldo9";
0596 regulator-min-microvolt = <1800000>;
0597 regulator-max-microvolt = <3000000>;
0598 regulator-boot-on;
0599 };
0600
0601 ldoln_reg: ldoln {
0602 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
0603 regulator-name = "ldoln";
0604 regulator-min-microvolt = <1800000>;
0605 regulator-max-microvolt = <1800000>;
0606 regulator-always-on;
0607 regulator-boot-on;
0608 };
0609
0610 ldousb_reg: ldousb {
0611 /* VDDA_3V_USB: VDDA_USBHS33 */
0612 regulator-name = "ldousb";
0613 regulator-min-microvolt = <3250000>;
0614 regulator-max-microvolt = <3250000>;
0615 regulator-always-on;
0616 regulator-boot-on;
0617 };
0618
0619 regen3_reg: regen3 {
0620 /* REGEN3 controls LDO9 supply to card */
0621 regulator-name = "regen3";
0622 regulator-always-on;
0623 regulator-boot-on;
0624 };
0625 };
0626 };
0627 };
0628 };
0629
0630 &i2c2 {
0631 pinctrl-names = "default";
0632 pinctrl-0 = <&i2c2_pins>;
0633
0634 clock-frequency = <100000>;
0635 };
0636
0637 &usbhshost {
0638 port2-mode = "ehci-hsic";
0639 port3-mode = "ehci-hsic";
0640 };
0641
0642 &usbhsehci {
0643 phys = <0 &hsusb2_phy &hsusb3_phy>;
0644 };
0645
0646 &usb3 {
0647 extcon = <&extcon_usb3>;
0648 vbus-supply = <&smps10_out1_reg>;
0649 };
0650
0651 &cpu0 {
0652 cpu0-supply = <&smps123_reg>;
0653 };
0654
0655 &dss {
0656 status = "okay";
0657
0658 pinctrl-names = "default";
0659 pinctrl-0 = <&dss_dpi_pins>;
0660
0661 port {
0662 #address-cells = <1>;
0663 #size-cells = <0>;
0664
0665 dpi_dvi_out: endpoint@0 {
0666 reg = <0>;
0667 remote-endpoint = <&tfp410_in>;
0668 data-lines = <24>;
0669 };
0670
0671 dpi_lcd_out: endpoint@1 {
0672 reg = <1>;
0673 remote-endpoint = <&lcd_in>;
0674 data-lines = <24>;
0675 };
0676 };
0677 };
0678
0679 &dsi2 {
0680 status = "okay";
0681 vdd-supply = <&ldo4_reg>;
0682 };
0683
0684 &hdmi {
0685 status = "okay";
0686 vdda-supply = <&ldo4_reg>;
0687
0688 pinctrl-names = "default";
0689 pinctrl-0 = <&dss_hdmi_pins>;
0690
0691 port {
0692 hdmi_out: endpoint {
0693 remote-endpoint = <&hdmi_connector_in>;
0694 lanes = <1 0 3 2 5 4 7 6>;
0695 };
0696 };
0697 };
