0001 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
0002 /*
0003 * Copyright (c) 2014 Protonic Holland
0004 */
0005
0006 #include <dt-bindings/gpio/gpio.h>
0007 #include <dt-bindings/input/input.h>
0008
0009 / {
0010 chosen {
0011 stdout-path = &uart4;
0012 };
0013
0014 reg_3v3: regulator-3v3 {
0015 compatible = "regulator-fixed";
0016 regulator-name = "3v3";
0017 regulator-min-microvolt = <3300000>;
0018 regulator-max-microvolt = <3300000>;
0019 };
0020
0021 reg_usb_h1_vbus: regulator-h1-vbus {
0022 compatible = "regulator-fixed";
0023 regulator-name = "h1-vbus";
0024 regulator-min-microvolt = <5000000>;
0025 regulator-max-microvolt = <5000000>;
0026 };
0027
0028 reg_usb_otg_vbus: regulator-otg-vbus {
0029 compatible = "regulator-fixed";
0030 regulator-name = "otg-vbus";
0031 regulator-min-microvolt = <5000000>;
0032 regulator-max-microvolt = <5000000>;
0033 gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
0034 enable-active-high;
0035 };
0036 };
0037
0038 &can1 {
0039 pinctrl-names = "default";
0040 status = "okay";
0041 };
0042
0043 &i2c1 {
0044 clock-frequency = <100000>;
0045 pinctrl-names = "default";
0046 pinctrl-0 = <&pinctrl_i2c1>;
0047 status = "okay";
0048 };
0049
0050 &i2c3 {
0051 clock-frequency = <100000>;
0052 pinctrl-names = "default";
0053 pinctrl-0 = <&pinctrl_i2c3>;
0054 status = "okay";
0055
0056 temperature-sensor@70 {
0057 compatible = "ti,tmp103";
0058 reg = <0x70>;
0059 };
0060 };
0061
0062 &uart4 {
0063 pinctrl-names = "default";
0064 pinctrl-0 = <&pinctrl_uart4>;
0065 status = "okay";
0066 };
0067
0068 &usbh1 {
0069 vbus-supply = <®_usb_h1_vbus>;
0070 phy_type = "utmi";
0071 dr_mode = "host";
0072 status = "okay";
0073 };
0074
0075 &usbotg {
0076 vbus-supply = <®_usb_otg_vbus>;
0077 pinctrl-names = "default";
0078 pinctrl-0 = <&pinctrl_usbotg>;
0079 phy_type = "utmi";
0080 dr_mode = "host";
0081 disable-over-current;
0082 status = "okay";
0083 };
0084
0085 &usdhc1 {
0086 pinctrl-names = "default";
0087 pinctrl-0 = <&pinctrl_usdhc1>;
0088 cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
0089 status = "okay";
0090 };
0091
0092 &usdhc3 {
0093 pinctrl-names = "default";
0094 pinctrl-0 = <&pinctrl_usdhc3>;
0095 bus-width = <8>;
0096 non-removable;
0097 no-1-8-v;
0098 no-sd;
0099 no-sdio;
0100 status = "okay";
0101 };
0102
0103 &iomuxc {
0104 pinctrl_can1: can1grp {
0105 fsl,pins = <
0106 MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b008
0107 MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b008
0108 >;
0109 };
0110
0111 pinctrl_i2c1: i2c1grp {
0112 fsl,pins = <
0113 MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
0114 MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
0115 >;
0116 };
0117
0118 pinctrl_i2c3: i2c3grp {
0119 fsl,pins = <
0120 MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
0121 MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
0122 >;
0123 };
0124
0125 pinctrl_uart4: uart4grp {
0126 fsl,pins = <
0127 MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
0128 MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
0129 >;
0130 };
0131
0132 pinctrl_usdhc1: usdhc1grp {
0133 fsl,pins = <
0134 MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
0135 MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
0136 MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
0137 MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
0138 MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
0139 MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
0140 MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
0141 >;
0142 };
0143
0144 pinctrl_usdhc3: usdhc3grp {
0145 fsl,pins = <
0146 MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
0147 MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
0148 MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
0149 MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
0150 MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
0151 MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
0152 MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
0153 MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
0154 MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
0155 MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
0156 MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
0157 >;
0158 };
0159
0160 pinctrl_usbotg: usbotggrp {
0161 fsl,pins = <
0162 MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
0163 MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
0164 >;
0165 };
0166 };
